Enclosure Overview
Top Cover
Switch
Addonics
T E C H N O L O G I E S
Ruby Cipher AES 256-bit ExDrive
RCED256ES & RCED256EU
Cipher Key
Cipher Key Socket
Drive Activity
LED
User’s Guide
Ruby Cipher key
Check to make sure you have the correct version of the Ruby Cipher key. The
key should match the label at the back of the drive enclosure.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a class B digital
device pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try and correct the interference by one or more of the following
suggestions.
Reorient or relocate the receiving antenna
Black label AES-256 stands for Ruby Cipher 256-bit key
Increase the distance between the equipment and the receiver
Connect the equipment to a different power outlet other than the one where receiver is
connected
Consult a certified television or radio technician
Power: Connect the power cable (provided) to the 5V power connector located at
the back of the enclosure.
Step 5 Mount the board to the bottom
cover.
Data:
Model: RCED256ES
Connect the eSATA to eSATA cable to the eSATA connector located at the back
of the enclosure and the other end of the eSATA cable to the eSATA connector
on your SATA host controller with eSATA ports.
Model: RCED256EU
Connect the eSATA to eSATA cable to the eSATA connector located at the back
of the enclosure and the other end of the eSATA cable to the eSATA connector
on the USB2.0 to eSATA adapter. You can now plug the adapter to a USB port
on your system.
Step 6 Put the top cover on by holding it in
near vertical position and sliding the two
metal clips inside the two small slots on the
rear of the bottom cover.
Powering On Enclosure:
Note: Be sure the Ruby cipher key is inserted into the drive enclosure prior to
turning on the power of the drive cradle. The hard drive will not be
detected by the computer if the power to the drive cradle is turned on
without the Cipher key. Under such condition, the power on the drive
cradle will have to be turned off and turned back on again with the
Cipher key already inserted into the drive enclosure in order to detect
the hard drive.
Step 7 Lower the front of the top cover and making sure the two covers lined up
properly. Tighten the small retaining screw on the front of the bottom cover to
close the enclosure.
To power on the enclosure, move the switch located at the front of the enclosure
to the EXT mode. When the switch is turned on, the LED light beside it would
light up to indicate power and also drive access.
Note: There are no drivers needed to use the eSATA cable as long as the
drivers are installed for the Serial ATA Controller card/chip. It is plug
and play.
Cable Connections
Brand New Hard drive must be partitioned and formatted first before a
drive letter is assigned by the OS.
Power connection
using 5V power adapter
Internal/External
or USB power cable
Power Switch
Technical Support
If you need assistance to get your unit functioning properly, please call Addonics
Technical Support. Our technical staff will be happy to assist you, but they will
need your help to do so. Calling the technical support staff without all the proper
information can be both time consuming and frustrating. Here are some tips to
help you out:
MODEL NUMBER – Please have this number on hand.
SYSTEM INFORMATION – Type of computer, peripherals, etc.
OPERATING SYSTEM – What version of Windows
WHAT’S THE TROUBLE? – Give enough information
about your problem so that we can recreate and diagnose it.
FREE Software Drivers for all Addonics Technologies
Products are available 24 hours per day at the
World Wide Web Site: www.addonics.com
Contact Information
Phone:
Fax:
408-573-8580
408-573-8588
Email:
Internet:
TECHNICAL SUPPORT
Phone:
Hours:
Email:
408-453-6212
8:30 am - 6:00 pm PST
|