27930
3. Plug the power supply into the power jack on the back
of the base and the other end into an electrical outlet.
The "charge" indicator comes on, verifying the battery
is charging.
1. Call the bank’s information line.
DIGITAL SECURITY SYSTEM
DEFAULT SETTING SELECTION
INTRODUCTION
RECEIVING AND STORING CALLS
2. Press theTONE button (*) after your call is answered.
3. Follow the voice instructions to complete your transaction.
40-Channel 2.4 GHz Caller ID with
CallWaiting CordlessTelephone
User's Guide
Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.
1. Press the flash/program button until DEFAULT
SETTING? 1YES 2NO shows in the display. “2NO” is
the default setting.
Your Caller ID phone stores and displays specific
information, provided by your local telephone company, to
subscribers of Caller ID or similar caller identification
services.You must subscribe to one of these services in
order to use this unit.
When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.
4. Hang up when finished.The phone returns to Pulse
(rotary) service.
Allow the phone to charge for 12 hours prior to first use.
If you don't properly charge the phone, battery
performance will be compromised.
When you place the handset in the base, the unit verifies
its security code. After a power outage or battery
replacement, you should place the handset in the base for
about 20 seconds to reset the code.
2. Use the CID Review (up or down arrow) button or the
handset number pad to scroll to 1YES or 2NO.
When the memory is full, a new call automatically replaces
the oldest call in memory. NEW appears in the display for
calls received that have not been reviewed. REPT indicates
that a new call from the same number was received more
than once.
4. Remove the handset from the cradle and set aside.Turn the
base over and align the four slots on the bottom of the
base with the four hook-tabs on the mounting bracket.
3. Press flash/program to store selection.You will hear a
confirmation tone.
HOLD
Your Caller ID phone enables you to:
•
•
•
•
Identify callers before you answer the phone.
View the time and date of each incoming call.
Record up to 40 Caller ID messages sequentially.
Know who called while you were away.
Press the hold button to put a call on hold. HOLD shows in
the display, and the handset antenna indicator flashes.To
release a line on hold, press the hold button again or pick
up an extension phone.
INSTALLATION
CORDLESS PHONE BASICS
5. Insert the hook-tabs into the slots and push upwards
until the mounting bracket snaps securely into place.
NOTE: Check with your local phone company
regarding name service availability.
VOLUME buttons
DESKTOP INSTALLATION
NOTE : For desktop charging only, the handset is able
6. Plug the telephone line cord into theTEL LINE jack on
the back of the base and the other end into a modular
jack. If desired, gather the extra telephone line cord
together, fasten with a wire tie, and store inside the wall
mounting bracket.
CID
review
button
CANCEL
To get the most from your new phone, we suggest that you
take a few minutes right now to read through this user's
guide.
TALK/
callback
button
to charge facing up or down.
REVIEWING RECORDS
Press the cancel button to cancel any command you
initiated. Press cancel to hang up after finishing a call.
As calls are received and stored, the display is updated to
let you know how many calls have been received.
FORMAT
IMPORTANT: In order to use this unit, you must
subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.
7. Slip the mounting holes on the bracket over the wall
plate posts and firmly slide the unit down into place
(wall plate not included).
button
redial/
delete
button
•
Press the CID review down button to scroll through the
call records from the most recent to the oldest.
FINDING THE HANDSET
3
k
c
a
llb
a
c
2
cancel
button
TALK
FORMAT
cancel
CID
This feature helps to locate a misplaced handset.
8. Place the handset in the cradle.
•
Press the CID review up button to scroll through the call
records from the oldest to the newest.
Press the PAGE button on the base.The handset beeps
continuously for about 2 minutes or until you press the
TALK button on the handset..
hold
RINGER
switch
NOTE : The phone is shipped in Tone Dialing Mode
from the manufacturer.
1
hold
button
3
6
DEF
1
2
ABC
JKL
IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.
4
GHI
MNO
5
TRANSFERRING CID RECORDS TO
MEMORY
TONE
button
NOTE: The ringer does not have to be on for this
feature to work.
7
PQRS
9WXYZ
CAUTION: Use only the ATLINKS USA, Inc.
5-2530 power supply that came with this unit.
Using other power supplies may damage the unit.
8TUV
PAUSE
button
*TONE
#
PAUSE
O
OPER
g
r
a
m
4
o
r
p
c
h
h
s
You may transfer a Caller ID record to your phone’s memory.
a
n
fla
mute
mem
CAUTION: When using telephone equipment,
there are basic safety instructions that should
always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
flash/
program
button
RINGER SWITCH
NOTE: It is important that you format CID records
correctly before storing in memory. It is not possible to
re-format CID records stored in memory.
1. Remove the battery compartment door on the handset,
insert the battery pack, plug the cord into the jack (inside
the compartment), and replace the compartment door.
SET UP
chan
button
The RINGER switch must be ON for the handset to ring
during incoming calls.
mute
button
mem
button
There are five programmable menus available: Language,
Area Code, RingerTone, SetTone/Pulse, and Default Setting.
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2. Set the RINGER switch (on the handset) to ON and place
the handset in the cradle on the base.
1. Use the CID review (up or down arrow) button to scroll
to the desired record.
VOLUME
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
THE LIGHTNING FLASH CAUTION: TO REDUCE THE RISK OF
AND ARROW HEAD
ELECTRIC SHOCK, DO NOT REMOVE
WITHIN THE TRIANGLE COVER (OR BACK). NO USER
LANGUAGE SETTING SELECTION
IS A WARNING SIGN
ALERTING YOU OF
“DANGEROUS
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING SIGN
ALERTING YOU OF
IMPORTANT
The VOLUME button controls the volume of the handset's
earpiece.There are four volume levels. VOL 1 is the lowest
level and VOL 4 is the loudest.
3. Plug the telephone line cord into theTEL LINE jack on
the back of the base and into a modular jack.
2. Press the mem button.
RECEIVING A CALL
INSTRUCTIONS
ACCOMPANYING THE
PRODUCT.
VOLTAGE” INSIDE THE
PRODUCT.
WARNING:TO PREVENT FIRE OR
ELECTRICAL SHOCK HAZARD, DO
NOT EXPOSETHIS PRODUCT TO
RAIN OR MOISTURE.
1. Press the flash/program button until “1ENGLISH 2FRA
3ESP “ shows in the display. “1ENGLISH “ is the
default setting.
3. Press the desired memory location. Example, press the
number 1 key to store the record in memory location 1.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
4. Plug the power supply into the power jack on the back
of the base and the other end into an electrical outlet.
The "charge" indicator comes on, verifying the battery
is charging.
1. Check the display to see who is calling.
2. Press theTALK button.
4. Press the mem button again to store.The unit beeps to
confirm.
VOICE MESSAGING
in use/VMWI
indicator
2. Use the CID review (up or down arrow) button or the
handset number pad to enter your selection.
BEFORE YOU BEGIN
We bring good things to life.
Provided your phone company
To replace a CID record stored in a memory location
with a new CID record:
MAKING A CALL
Allow the phone to charge for 12 hours prior to first use.
If you don't properly charge the phone, battery
performance will be compromised.
offers voice messaging service
3. Press flash/program to store selection.You will hear a
confirmation tone.
To make a call, press theTALK button before you dial and
press it again to hang up.
and you subscribe to it, the in use/
in use/VMWI
PARTS CHECKLIST
charge/PAGE
indicator
1. Repeat steps 1 through 3.
VMWI indicator on the base
charge
FCC REGISTRATION INFORMATION
flashes when the phone is not in
use to indicate there is a message
waiting. It stops flashing after the
message has been reviewed.
PAGE
Make sure your package includes the items shown here.
2. Press the mem button and REPLACE MEMO? shows in
the display.
CAUTION: Use only the ATLINKS USA, Inc.
5-2530 power supply that came with this unit.
Using other power supplies may damage the unit.
AREA CODE SELECTION
1. Press the flash/program button until “SET AREA CODE - - -”
shows in the display. “- - -” is the default setting.
Your telephone equipment is registered with the Federal
Communications Commission and is in compliance with parts 15 and
68, FCC Rules and Regulations.
REDIAL
PAGE
button
3. Press mem again and the new CID record replaces the
old CID record in that memory locatio.The unit beeps
twice to confirm.
While the phone is on, press the redial/delete button to
redial the last number you dialed (up to 32 digits). If you
get a busy signal, and want to keep dialing the number,
just press redial/delete again (you don't have to turn the
phone off and back on).
k
callbac
1
Notification to the LocalTelephone Company
TALK
FORMAT
CID
de
let
e
re
l
ce
d
ia
n
ca
l
hold
On the bottom of this equipment is a label indicating, among other
information, the FCC Registration number and Ringer Equivalence
Number (REN) for the equipment.You must, upon request, provide
this information to your telephone company.
in use/VMWI
charge
Belt clip
1
3
6
DEF
NOTE : The phone is shipped in Tone Dialing Mode
from the manufacturer.
2
ABC
JKL
2. Use the handset number pad to enter your three digit
area code.
4
GHI
MNO
5
CALLER ID FEATURES
PAGE
7
PQRS
9WXYZ
8TUV
Mounting bracket
*TONE
#
PAUSE
O
OPER
ra
m
r
o
g
p
cha
n
flash
mute
3. Press flash/program to store selection.You will hear a
confirmation tone.
DELETING RECORDS
The REN is useful in determining the number of devices you may
connect to your telephone line and still have all of these devices
ring when your telephone number is called. In most (but not all)
areas, the sum of the RENs of all devices connected to one line
should not exceed 5. To be certain of the number of devices you may
connect to your line as determined by the REN, you should contact
your local telephone company.
Number of calls
Time
Date
Base
Handset
Use the redial/delete button to erase the record currently
shown in the display or all records.
WALL MOUNT INSTALLATION
FLASH
RINGER TONE SELECTION
Use the flash/program button to activate custom calling
services such as call waiting or call transfer, which
are available through your local phone company.
DELETING THE CURRENT RECORD
1. Press the flash/program button until “SET RINGER
TONE123” shows in the display. “1” is the default setting.
Telephone
line cord
AC power
supply
Handset battery
Notes
1. Make sure the phone is OFF (not inTALK mode).
• This equipment may not be used on coin service provided by the
telephone company.
TIP: Don’t use the TALK button to activate custom
calling services such as call waiting, or you’ll hang up
the phone.
2. Use the CID review (up or down arrow) buttons to
display the desired Caller ID record.
2. Use the CID review (up or down arrow) button or the
handset number pad to scroll to 1, 2, or 3.
MODULAR JACK REQUIREMENTS
• Party lines are subject to state tariffs, and therefore, you may not
be able to use your own telephone equipment if you are on a
party line. Check with your local telephone company.
You need an RJ11 type modular phone jack, which
is the most common type of phone jack and might
look like the one pictured here. If you don’t have a
modular jack, call your local phone company to
find out how to get one installed.
4
3. Press redial/delete.The display shows DELETE?
Caller ID phone number
Caller ID name
3. Press flash/program to store selection.You will hear a
confirmation tone.
• Notice must be given to the telephone company upon
ck
lba
cal
3
6
T
ALK
FORMA
T
CID
permanent disconnection of your telephone from your line.
Rights of theTelephone Company
4. Press redial/delete again to erase the record.The display
shows NEXT CID RECORD.
de
le
te
re
d
l
ial
ce
n
a
c
hold
This unit receives and displays information transmitted by
your local phone company.This information can include
the phone number, date, and time; or the name, phone
number, date, and time.The unit can store up to 40 calls
for later review.
2
1
3
DEF
1
2
ABC
JKL
IN USE INDICATOR
4
GHI
6
MNO
5
Should your equipment cause trouble on your line which may harm
the telephone network, the telephone company shall, where
practicable, notify you that temporary discontinuance of service may
be required. Where prior notice is not practicable and the
circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such
temporary discontinuance, the telephone company must: (1) promptly
notify you of such temporary discontinuance; (2) afford you the
opportunity to correct the situation; and (3) inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth
in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action
is required in the operation of its business and not inconsistent
with FCC Rules and Regulations. If these changes are expected to
affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to
allow you to maintain uninterrupted service.
5
7
PQRS
9WXYZ
8TUV
TONE/PULSE DIALING SELECTION
1. Press the flash/program button until “SET TONE/PULSE”
shows in the display. “1TONE” is the default setting.
*TONE
#
PAUSE
O
OPER
o
g
ra
m
r
p
ch
an
The phone is ON when the indicator on the handset
antenna is lit and the page/ in use indicator on the base is
lit.The antenna indicator and the in use indicator on the
base flashes when you receive a call.
flash
mute
mem
DELETING ALL RECORDS
7
2
1. Make sure the phone is OFF (not inTALK mode).
INSTALLATION NOTE: Some cordless telephones
operate at frequencies that may cause interference to
nearby TVs microwave ovens, and VCRs. To minimize
or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a
TV, microwave ovens, or VCR. If such interference
continues, move the cordless telephone farther away
from these appliances. Certain other communications
devices may also use the 2.4 GHz frequency for
communication, and, if properly set, these devices may
interfere with each other and/or your new telephone.
If you are concerned with interference, please refer to
the owner’s manual for these devices on how to
properly set channels to avoid interference. Typical
devices that may use the 2.4 GHz frequency for
communication include wireless audio/video senders,
wireless computer networks, multi-handset cordless
telephone systems, and some long-range cordless
telephone systems.
Because it is necessary to charge the handset for 12 hours
prior to connecting the phone for use the first time, it is
better to leave the unit on a flat surface during initial
charge before attempting to hang it on the wall.
2. Use the CID review (up or down arrow) buttons to
display any Caller ID record.
2. Use the CID review (up or down arrow) button or the
handset number pad to scroll to 1TONE or 2PULSE.
CALLER ID WITH CALL WAITING
3. Press and hold redial/delete button until the unit beeps
and DELETE ALL? shows in the display.
CHANNEL BUTTON
Provided you subscribe to Caller ID with Call Waiting
service from your phone company, you are able to see who
is calling when you hear the call waiting beep.The caller
identification information appears in the display after you
hear the tone.
3. Press flash/program to store selection.You will hear a
confirmation tone.
While talking, you might need to manually change the
channel in order to get rid of static. Press and release the
chan button to advance to the next clear channel.
1. Remove the battery compartment door on the handset,
insert the battery pack, plug the cord into the jack (inside
the compartment), and replace the compartment door.
4. Press redial/delete again to erase all records.The display
shows NO CALLS.
2. Set the RINGER switch (on the handset) to ON and place
the handset in the cradle on the base.
•
Press the flash button to put the current person on hold
so that you can answer the incoming call.
TEMPORARY TONE
This feature enables pulse (rotary) service phone users to
access touch-tone services offered by banks, credit card
companies, etc., by pressing theTONE button to temporarily
make the phone touch-tone compatible.To get information
about your bank account, for example, you would:
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid
Compatibility.
IMPORTANT: In order to use the Caller ID functions
with this unit, you must subscribe to either the
standard Name/Number Caller ID Service or Caller
ID with Call Waiting Service. To know who is calling
while you are on the phone, you must subscribe to
Caller ID with Call Waiting Service.
FCC NUMBER IS LOCATED ONTHE CABINET BOTTOM
REN NUMBER IS LOCATED ONTHE CABINET BOTTOM
ATLINKS USA, Inc.
10330 North Meridian Street
Indianapolis, IN 46290
© 2001 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) ® Registrada(s)
Model 27930A
15727290 (Rev. 0 DOM E)
01-27
Printed in China
|