TM
EVANSTON 8 TENT
MODEL 2000001587
9. Attach frame clips along edges of tent
Before you begin
to the black & grey Main Poles. (Fig. 3)
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
Fig. 3
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
10. Stretch tent until taut, then secure metal
loops located on both sides and four
corners of tent with stakes. (Fig. 4)
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Fig. 4
To Attach Rainfly
Pole Descriptions
1. Drape Rainfly over tent with green vestibule flaps located
at the front of the tent. (Fig 5).
Pole
Pole
Pole
Description
Qty. Dia.
Repair Kit Replacement Kit
NOTE: Hook and loop fasteners, located on seams of
underside of Rainfly, should be centered over black & grey
Main Poles.
Main Pole, black
2
1
1
1
11mm 501000539
11mm 501000539
11mm 501000539
7.9mm 501000569
501000549
Main Pole, grey
501000549
501000549
501000568
Rainfly Pole, black, long
Awning Pole, black, short
Vertical Door Pole, black,
short w/rubber tips
Door Pole, black,
long w/rubber tips
2. Insert the long, black, Rainfly Pole through sleeve in under-
side of Rainfly above front door of tent. (Fig. 5)
1
1
6.3mm 501000543
6.3mm 501000543
501000545
501000545
Sleeve with Grey Trim
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. (Fig. 1)
Rainfly
Black, Shock-corded
Rainfly Pole
2. Assemble all poles by interlocking the shock-corded,
sections together.
Door
3. Insert black Main Poles through the black trimmed sleeves
on top of tent forming an X”.
4. Insert grey Main Pole through grey trimmed sleeve, in front
of tent. Make sure grey Main Poles overlap the black Main
Poles. (Fig. 1)
Front of Tent
Vestibule Flap
Vestibule Flap
Fig. 5
3. Insert short, black, thin Awning Pole through sleeve in under-
side of Rainfly above window at back of tent. (Fig. 6)
4. Insert metal tip into grommet on tent seam at back of tent
(Fig. 6A). Go to opposite end of Awning Pole and gradually
apply pressure to pole forming an arch; then insert metal tip
into grommet.
Fig. 1
Sleeves with Black Trim
Grey, Shock-corded
Sleeve with
Main Pole
Grey Trim
Door
Fig. 6
Approximate
Grommet
location
on tent
Front of Tent
Black, Shock-corded Main Poles
Rainfly Sleeve
Awning Pole
5. Insert end of each black Main Pole into pins located in
the corners of the tent. (Fig. 2 & 2A)
6. Go to opposite end of each black Main Pole and gradually
apply pressure to each forming arches. Insert the pin into
each pole end at the corners of tent. (Fig. 2 & 2A)
7. Insert end of the grey Main Pole into pin located on the sides
of the tent. (Fig. 2 & 2B)
Awning
Pole
Back
of Tent
Grommet
Approximate
6A
Grommet
location
on tent
5. Insert end of each black Rainfly Pole into
pin on either side of front door. (Fig. 7)
6. Go to opposite end of Rainfly Pole and
gradually apply pressure to form an arch.
Insert the pin into pole end at other
side of the door. (Fig. 7)
7. Locate all hook & loop fasteners on
underside of Rainfly and wrap around
all Main Poles, Awning & Rainfly Pole
to secure. (Fig. 8)
8. Go to opposite end of the grey Main Pole and gradually apply
pressure to form an arch. Insert the pin into pole end at the
side of tent. (Fig. 2 & 2B)
Fig. 7
Fig. 8
2A
2B
NOTE: Make sure longer hook & loop
fastener on Rainfly is secured around
grey and black Main Poles where they
cross. (Fig. 9)
Door
Fig. 9
Front of Tent
Fig. 2
(continued on other side)
|