Cooper Lighting Indoor Furnishings V90229 1N User Manual

INSTALLATION INSTRUCTIONS  
V90229-1N  
COMBOLIGHT  
R
TRIMLESS  
Avoid Fire or Electric Shock  
  
Page 1 of 3  
THIS PRODUCT MUST BE INSTALLED IN  
ACCORDANCE WITH THE APPLICABLE  
INSTALLATION CODE BY A PERSON  
FAMILIAR WITH THE CONSTRUCTION AND  
OPERATION OF THE PRODUCT AND THE  
HAZARDS INVOLVED.  
*Installation Instructions for qualified electricians only.  
*Install per National Electrical Code and local regulations.  
*Read Installation Instructions completely before installation.  
*Failure to follow Installation Instructions may void warranties.  
FIXTURE MOUNTING:  
1. First remove TRIMLESS INSERT from Housing by pulling straight out.  
See Fig 1. Fixture must be mounted using either BUTTERFLY MOUNTING  
BRACKETS or HANGER BARS (Contact RSA Dealer for HANGER BARS).  
HOUSING  
SCREW  
JBOX  
JBOX COVER  
Figure 3  
TRIMLESS INSERT  
CEILING MATERIAL INSTALLATION:  
Figure 1  
8. A clean, square hole in the CEILING MATERIAL must be cut. Install the  
ceiling material below housing as seen in Fig 4.  
INSTALLATION NOTE:  
9. Replace the TRIMLESS INSERT into the HOUSING by pushing until flush  
with the CEILING MATERIAL as seen in Fig 4. Using the OUTER  
ALIGNMENT HOLES on the TRIMLESS INSERT, screw the TRIMLESS  
INSERT into the HOUSING using DRYWALL SCREWS into the Outer  
Holes on the TRIMLESS INSERT.  
DO NOT install insulation within 3in of any part of the Luminaire.  
Blinking light of this thermally protected Luminaire may indicate overheating.  
BUTTERFLY MOUNTING:  
10. Smooth out MUDDING COMPOUND / TAPE from around aperture to  
surrounding areas of DRYWALL as seen in Fig 4.  
2. Fixture comes equipped with universal BUTTERFLY MOUNTING  
BRACKETS that can take common 1" or 1-1/2" black iron or galvanized  
MOUNTING CHANNELS (supplied by others). See Fig 2.  
OUTER ALIGNMENT HOLES  
3. Position fixture so the MOUNTING CHANNELS lie on top of the ceiling  
runners.  
4. Fasten MOUNTING CHANNELS securely to ceiling runners.  
5. Secure MOUNTING CHANNELS to universal BUTTERFLY MOUNTING  
BRACKETS with wire tie downs.  
6. The BUTTERFLY MOUNTING BRACKETS are height-adjustable and  
should be set so that the APERTURE COLLAR will be flush with the  
finished ceiling plane.  
MOUNTING  
CHANNEL  
OUTER ALIGNMENT HOLES  
BUTTERFLY  
MOUNTING  
BRACKET  
HEX  
SCREW  
HOUSING  
APERTURE  
COLLAR  
DRYWALL SCREW  
Figure 2  
ELECTRICAL:  
TRIMLESS  
INSERT  
DRYWALL  
7. Remove the JBOX COVER from the JBOX by removing the four SCREWS.  
Connect supply lead wires to junction box lead wires in accordance with  
your local electrical code(s) or N.E.C. Replace JBOX COVER onto JBOX,  
securing with SCREWS. See Fig 3.  
MUDDING  
COMPOUND  
Figure 4  
 
INSTALLATION INSTRUCTIONS  
V90229-3  
COMBOLIGHT  
R
LAMPHOLDER  
Avoid Fire or Electric Shock  
  
Page 3 of 3  
THIS PRODUCT MUST BE INSTALLED IN  
ACCORDANCE WITH THE APPLICABLE  
INSTALLATION CODE BY A PERSON  
FAMILIAR WITH THE CONSTRUCTION AND  
OPERATION OF THE PRODUCT AND THE  
HAZARDS INVOLVED.  
*Installation Instructions for qualified electricians only.  
*Install per National Electrical Code and local regulations.  
*Read Installation Instructions completely before installation.  
*Failure to follow Installation Instructions may void warranties.  
19. To replace the COVER RING:  
Push the COVER RING onto the BACK RING by lining up the  
BAYONET SLOTS (see Fig. 11) with the two (2) PINs in the BACK RING.  
GIMBAL BRACKET  
(Standard Position)  
PIN  
BACK RING  
BAYONET  
SLOTS  
GIMBAL BRACKET  
(Rotated 180° to  
"Down" Position)  
COVER  
RING  
Figure 9  
Figure 11  
17. Once removed, flip the two (2) GIMBAL BRACKETs around (180°) and  
tighten the joint if necessary. See Fig. 9.  
If necessary, please see Step 21 for gimbal tightening instructions.  
20. Once lined up, push straight back until the COVER RING stops, then  
while keeping the COVER RING pushed back, turn clockwise until it  
pushes forward again slightly. See Fig. 12.  
18. Reinsert the lamp ring assembly by turning it counter-clockwise into the  
SLOTs on the GIMBAL BLOCKs. Re-tighten the two (2) SET SCREWs  
in the GIMBAL BLOCKs. The lamp ring assy should now be oriented in  
the "up position". See Fig. 10.  
GIMBAL RING  
GIMBAL  
BLOCK  
SNOOT  
COVER RING  
(AS INSTALLED)  
Figure 12  
21. Gimbal tightening instructions:  
The lamp ring is intended to give positive tension at the PIVOT JOINTS  
so the lamp ring can be aimed by hand and held in place by tension.  
*If a stronger, more secure lock is required then the PIVOT JOINTS (hex  
screws) may be tightened clockwise with a hex wrench tool. See Fig. 6.  
*Please note that in some conditions the COVER RING will need to be  
removed to gain access to the inner PIVOT JOINTS.  
SLOT  
SET SCREW  
Figure 10  
 

Code Alarm Remote Starter CSM 3 User Manual
Compaq Projector MP1600 User Manual
Compaq Saw FS8500RS User Manual
Conair Scale WW31 User Manual
Cooper Lighting Landscape Lighting LQL1500 User Manual
CPG Printer SP40 User Manual
D Link Network Router VDI 624 User Manual
Fundex Games Board Games 2522 User Manual
Geemarc Cordless Telephone CL10 User Manual
Globalsat Technology GPS Receiver GH 601 User Manual