Craftsman Home Security System 13953684 User Manual

®
Model 139.53684  
Keyless Entry  
To comply with FCC rules, adjustment or modification of receiver and/or  
transmitter is prohibited, except for changing the password setting and replacing  
the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.  
Features  
For use with any SECURITYcompatible  
garage door opener receiver.  
Personalized Password: Up to 10,000  
possible combinations. Password can be easily  
changed if desired.  
WARNING  
Children operating or playing with a garage door opener can  
injure themselves or others. The garage door could close and  
cause serious injury or death. Do not allow children to operate the  
wall push button(s) or remote control(s).  
A moving garage door could injure or kill someone under it.  
Activate the opener only when you can see the door clearly, it is  
free of obstructions, and is properly adjusted.  
Temporary password: Can be added for visitors or service  
persons. This temporary password can be limited to a programmable  
number of hours or a programmable number of entries.  
Rolling Code: While your password remains constant until you  
change it, the code between the Keyless Entry and the receiver  
changes with each use, randomly accessing over 100 billion new  
codes.  
Operation: Opener activates when 4-digit password and Enter button  
is pressed.  
If wrong numbers are accidentally pressed, correction can be made  
immediately. The Enter button will transmit only the last four digits.  
The Keypad will blink for 15 seconds after the password is  
transmitted. During that time the Enter button can be used to stop or  
reverse the door travel.  
The Lock feature on openers with premium door controls is designed  
to prevent operation of the door from portable transmitters.  
However, the door will open and close from the door control push  
button and the Keyless Entry.  
Installation  
Keypad  
The recommended  
mounting locations for  
Exterior Front Wall  
1-Piece or  
Sectional Door  
sectional and one-piece  
doors are shown in  
Figure 3. You can select  
another location if you  
prefer. However, the  
keypad must be  
Door Jamb Edge  
(Optional Location  
for 1-Piece Door)  
Door Jamb Face  
SECTIONAL DOOR ONLY  
installed within sight of  
the door.  
KEYPAD MUST BE INSTALLED  
WITHIN SIGHT OF THE DOOR  
Setting the Personal Entry Password  
We recommend that you program your password now, before  
you install the Keyless Entry. Then you can test the reception  
at the mounting location before you proceed further.  
For a one-piece door,  
Figure 3  
use the optional location shown in the  
illustration (on the edge of the door jamb) to avoid injury  
as the door swings up and out.  
Choose a 4-digit password using the numbers from 0 to 9 (a  
number can be used more than once, for example, 4,0, 4,1.)  
Test the reception of the Keyless Entry by operating your  
opener from the selected location. Change the location if  
necessary.  
If you have a Premium Control Console:  
Door Control  
Push button  
1. With the door closed, press the four buttons for  
the password, then press and hold Enter.  
Keypad  
Cover  
Open the keypad and remove the  
battery compartment screw and  
cover to access the bottom  
mounting hole (Figure 4).  
2. Press and hold the light button on the door  
control, Figure 1.  
LIGHT  
3. Press and hold the door control push button.  
LOCK  
Center the keypad at eye level  
against the selected location. Mark  
4 1/4" up the centerline from the  
bottom and drill a 1/8" pilot hole.  
Install top mounting screw, allowing  
1/8" to protrude above surface.  
Position keypad on screw head and  
adjust for snug fit.  
4. After the opener light flashes, release all  
buttons.  
Bottom  
mounting hole  
Light  
Figure 1  
If you do not have a Premium Control Console:  
Battery  
1. Enter the four digit password desired, then press and hold  
Enter.  
Battery  
Cover  
2. Press and release the SRT (learn) button on the door  
opener panel, Figure 2.  
With cover open so bottom  
mounting hole is visible, use a punch to  
mark hole. Remove keypad and drill 1/8" pilot hole. Replace  
keypad and complete installation with bottom screw, using  
care to avoid cracking plastic housing. Do not overtighten.  
Figure 4  
3. After the opener light flashes, release the Enter button.  
Test by pressing your password, then press Enter. The door  
should begin to move.  
This procedure can be repeated with a different password for  
use with a second garage door opener.  
Replace the battery cover.  
Orange  
SRT (learn)  
Button  
1
2
3
Figure 2  
Side two contains instructions for changing the personal  
entry password and setting a temporary password.  
Security✚  
Garage Door Opener  
9
9
1
1
Yellow  
Indicator  
Light  
7
7
3
3
5
5
KG  
KG  
1
 

Code Alarm Remote Starter CA 411 User Manual
Craftsman Pressure Washer 919762000 User Manual
Craftsman Trimmer 91777342 User Manual
Cuisinart Blender 09CE13231 User Manual
Estate Oven 3150250 User Manual
Euro Pro Iron EP36 User Manual
Fellowes Paper Shredder 53C User Manual
Garland Griddle ECG User Manual
Generac Power Systems Portable Generator 004988 2 User Manual
Genicom Computer Hardware P45 User Manual