Creek Audio Home Theater System Evolution 2 User Manual

EVOLUTION 2  
INTEGRATED AMPLIFIER  
DESIGNED AND ENGINEERED  
IN THE UNITED KINGDOM  
OPERATING INSTRUCTIONS  
Thank you for purchasing the Creek EVOLUTION 2. You are now in possession of a State of the Art  
integrated amplifier. The functions and operation of the EVOLUTION 2 are very simple. However, the  
following notes are provided to explain all aspects of its design and use.  
MAINS CONNECTION  
When unpacking the amplifier please keep the packing material in a safe place for possible future use. In  
the pack there is a separate mains cable suitable for connecting to the mains supply in the country of use.  
The IEC socket end of the cable should be firmly inserted into the connector on the rear panel marked  
"Mains Input".  
Before switching on the amplifier check the voltage selector switch on the rear panel to ensure it is set  
correctly to the voltage of the country in which the amplifier is being used. Remember, do not overload  
the mains wall socket with too many plugs or adaptors. The high quality performance of the amplifier  
will be impaired if the electrical supply to it is in poor condition. If in doubt, consult a qualified electrician  
or your dealer.  
The ‘Mains Input’ connection is also fitted with a fuse. The value is clearly stated on the rear panel.  
INPUT CONNECTION AND SWITCHING  
The rotary selector switch on the left-hand side of the amplifier is used to select and listen to any of the  
desired inputs. There are four inputs plus tape, which is selected by the button marked tape. The  
selected input will appear in the display.  
All line level inputs have the same sensitivity. It is not absolutely necessary to use the precise inputs as  
designated, with the exception of the AV Direct. You may, for example, plug a CD player into the Tuner  
input and obtain exactly the same result or performance as the dedicated CD input. However, you need  
to be aware that the front panel display will always reflect the input as designated on the rear panel.  
Therefore our recommendation would always be to connect to the designated input.  
The AV Direct input is for use with a surround sound processor. This input caters specifically for those  
people who are more than happy with their AV solution, but not happy with the stereo option. To  
connect from a processor, it is necessary to run an interconnect from the front pre-outs to the AV Direct  
input. The Evolution 2 amplifier then becomes a standalone amplifier for front speaker use in 5.1 mode.  
When the AV Direct input is selected in this configuration, the Evolution 2’s signal level is not controlled  
by its volume knob.  
The pre-amp output and the power amp input is available through RCA sockets on the rear panel.  
However, when using an external device, such as a sub-woofer to extend the lower frequencies of your  
stereo speakers for example, the sub-woofer should be connected to the pre-amp output.  
For added flexibility, the first input on the EVOLUTION 2 can be used either for vinyl disc or auxiliary line.  
To connect your turntable, it is necessary to have the optional Sequel phono plug-in board fitted.  
Alternatively Creek Audio produces a separate range of phono pre-amplifers, which should be connected  
to the Aux input.  
 
EVOLUTION 2 INTEGRATED AMPLIFIER OPERATING INSTRUCTIONS  
POWER CONSUMPTION  
It is appreciated by hi-fi enthusiasts that leaving equipment powered up continuously can improve the  
performance. However, this small improvement in sound quality comes at the expense of higher power  
consumption from the mains, which will cost more for your electricity and also reduced working life of the  
product.  
We recommend that if the equipment is not being used for a period of time, it would be better to switch it off from  
the mains switch on the front panel. Normal performance can be achieved in a short period of time.  
OPERATING THE EVOLUTION 2  
Make sure that the amplifier is on a suitable table, shelf or hi-fi equipment cabinet.  
It is important to allow adequate ventilation to the heat-sink in the centre of the unit. Avoid obstruction of the  
ventilation slots on the top and bottom of the amplifier. It may be necessary to place the amplifier on the top of  
other equipment, or a separate shelf to allow for this.  
Switch on the amplifier by pressing the push button marked Power on the right hand side of the front panel. The  
power button on the remote handset does not turn on the amplifier. You will note that once switched on, the  
amplifier shows a pre-set moderate turn on volume level.  
Select the desired input from either the rotary selector or remote handset. Adjust the volume and settle down to  
listen. To switch off the amplifier, press the power button.  
Your EVOLUTION 2 amplifier is designed to give you years of reliable use. If you need more assistance, it is always  
advisable to go back to the supplying dealer for his expert help. If you are unfortunate enough to need service  
work to be carried out on your amplifier, it should be returned to your dealer in the original packing material if  
possible.  
REMOTE CONTROL  
Creek’s SRC 3 remote control handset allows the user to operate the volume control, input selection and mute by  
an infra-red signal using NEC codes. It should be noted that the Creek SRC3 remote handset will operate both  
Creek’s EVOLUTION and DESTINY range of products as well as some older Creek products. It transmits both NEC  
and RC5 codes concurrently. In the case of Evolution 2 the SRC3 is not able to power up the mains.  
The input button (on the left hand side of the handset beneath the numeric keys) will sequence through all  
available inputs.  
To mute the sound, press the mute button in the centre of the main control buttons. Pressing it a second time  
returns the amplifier to the previous level at which it was playing.  
Volume down and volume up buttons are on the left and right of the centre controls of the handset.  
The display button found on the top right hand side of the remote dims/brightens the display. The remaining  
buttons are for use with other source products.  
RADIO INTERFERENCE  
The Creek EVOLUTION 2 amplifier is designed to work properly in normal domestic operating conditions.  
However, the amplifier's performance could be affected if sited near to a radio transmitter such as a mobile  
phone etc.  
Page Three  
 
EVOLUTION 2 INTEGRATED AMPLIFIER OPERATING INSTRUCTIONS  
SPECIFICATION  
POWER OUTPUT (both channels into 8W)  
POWER OUTPUT (one channel into 8W)  
POWER OUTPUT (one channel into 4W)  
PEAK OUTPUT CURRENT INTO 1W  
TOTAL HARMONIC DISTORTION (20 Hz to 20 kHz)  
FREQUENCY RESPONSE  
80 Watts  
90 Watts  
145 Watts  
> 10 Amps RMS  
< 0.05%  
5 Hz to 50 kHz - 1 dB  
> 25 V per mS  
x 52  
SLEW RATE  
GAIN  
INPUT SENSITIVITY - One channel driven/8W 480 mV line input  
PRE-AMP OUTPUT LEVEL  
Follows input signal level via volume control  
SIGNAL TO NOISE RATIO (‘A’ weighted)  
SEPARATION (line inputs)  
> 90 dB  
> 60 dB at 1 kHz  
MM PHONO SENSITIVITY & IMPEDANCE  
MC PHONO SENSITIVITY & IMPEDANCE  
POWER CONSUMPTION (at idle)  
POWER CONSUMPTION (full power 10% THD)  
WEIGHT (net)  
3.5 mV 47 kW(when fitted)  
0.75 mV 1 kW(when fitted)  
40 W  
340 W  
8.6 kgs 19 lbs  
SIZE (W x H x D)  
430 x 80 x 340 mm 17 x 3.2 x 15.5 ins  
MAINS VOLTAGE  
Mains voltage selector switch on rear panel  
@ 60Hz  
@ 50Hz  
110/120V North America  
220/240V Europe, Asia and UK  
REMOTE HANDSET  
Creek SRC3  
Creek Audio Ltd reserves the right to change or modify the specification of its products without prior warning.  
If within two years of purchase date your Creek EVOLUTION proves to be defective for any reason other than  
accident, misuse, neglect, unauthorized modification, or fair wear and tear, Creek Audio Ltd. will, at its discretion,  
replace the faulty parts without charge for labour or return carriage within the United Kingdom. This warranty is  
valid only in the United Kingdom and given in addition to statutory rights. Service enquiries outside the United  
Kingdom should be addressed first to the supplying dealer and/or the Creek distributor/importer. Warranties  
granted in these countries are entirely at the discretion of the distributor.  
CREEK AUDIO LTD  
12 Avebury Court, Mark Road, Hemel Hempstead HP2 7TA United Kingdom  
Telephone: +44 (0)1442 260146 Fax: +44 (0)870 6220846  
E & O E  
 

Concord Camera Digital Camera Eye Q Easy Digital Camera User Manual
Cooper Bussmann Switch EDSC2199 User Manual
Cub Cadet Lawn Mower 11A 702A101 User Manual
Delta Electronics Power Supply SILM720 User Manual
Digital Foci Digital Photo Frame F7 129 User Manual
Dynex Camcorder Accessories 09 0406 User Manual
Fujitsu Flat Panel Television PDS4229W User Manual
GE Answering Machine 29861 User Manual
GE Monogram Oven ZSC1000 User Manual
GE Ventilation Hood BF100S User Manual