Dynasty Spas Hot Tub MC MP CE User Manual

MC-MP-CE Spa Pack •  
The Quick Reference Card provides a quick overview of your spa's main functions and the operations  
accessible with your digital control pad. Note that some functions require the use of the K-4 keypad (10 keys). *  
Starting Pump 1:  
Turning the light on:  
Press Pump 1 to turn Pump 1 on at low speed.  
Press a second time to turn Pump 1 to high  
speed. A third time turns Pump 1 off. A built-in  
timer automatically turns pump off after 20 min-  
utes, unless it has been manually deactivated.  
Two-intensity spa light:  
To advance to the next color/display setting, press  
Light key twice. The LEDs will go off with the first  
press, then back on in the next setting with the  
second press. If the LEDs remain off for more  
than 5 sec., the color/ display sequence will reset  
and start back at the beginning the next time the  
Light key is pressed. Color/ display sequences are:  
Press Light key to turn light on at high intensity.  
Press a second time to turn light to low inten-  
sity. A third time turns light off.  
One-intensity spa light:  
Press Light key to turn light on.  
Press a second time to turn light off.  
The "Pump 1" indicator lights up when  
Pump 1 is on at high speed. It flashes  
when Pump 1 is on at low speed.  
1• LEDs light up and slowly cycle through all  
six colors. The slow cycle restarts at the  
beginning and repeats.  
In both cases, a built-in timer turns light off after  
2 hours, unless manually deactivated first.  
2• LEDs light up and remain on in Aqua.  
3• LEDs light up and remain on in Purple.  
4• LEDs light up and remain on in Blue.  
5• LEDs light up and remain on in Gold.  
6• LEDs light up and remain on in Green.  
7• LEDs light up and remain on in Red.  
8• LEDs light up for 2 sec., flash off, then  
flash on in the next color until all six colors  
have been displayed. The flashing cycle  
then repeats itself.  
The "Light" indicator is displayed when  
light is on at high intensity. It flashes  
when light is on at low intensity.  
Starting Pump 2:  
Dual-speed pump system:  
Press Pump 2 to turn Pump 2 on at low speed.  
Press a second time to turn pump to high speed.  
A third time turns pump off.  
Fiber Box Option: If your spa has an optional  
fiber box, press Light key to turn fiber box  
(motor & light) on. Press a second time to turn  
fiber box motor off and leave light on. A third  
time turns both motor and light off. A built-in  
timer turns fiber box off after 2 hours, unless it  
has been manually deactivated. The "Light"  
indicator is displayed when fiber box light is on.  
It flashes when fiber box motor and light are on  
at the same time.  
Single-speed pump system:  
Press Pump 2 to turn Pump 2 on.  
Press a second time to turn Pump 2 off.  
9• LEDs flash on/off quickly for a strobe light  
effect. A built-in timer turns lights off after  
2 hours unless manually deactivated first.  
In both cases, a built-in timer turns Pump 2 off  
after 20 minutes, unless it has been manually  
deactivated.  
The "Light" icon is displayed  
when LED light is on.  
The "Pump 2" indicator lights up when  
Pump 2 is on. With a dual-speed pump,  
it will flash when Pump 2 is on at low speed.  
LED Light Option: If spa has an optional LED  
light, Press Light key to turn LED lights on.  
Standby mode:  
Starting the blower:  
Press and hold Filter key for 5 seconds to turn  
the system down (i.e. to set it to Standby  
mode) for 60 minutes. The display toggles  
between "SBY" message and the time re-  
maining. All keys are then disabled, unless  
you press Filter key to reactivate the system  
before the expiration of the 60-minute delay.  
Starting Pump 3: *  
Press Pump 3/Off to turn Pump 3 on. Press  
a second time to turn Pump 3 off. A built-in  
timer automatically turns pump off after  
20 minutes, unless manually deactivated first.  
Press Blower to turn blower on at high speed.  
Press a second time to turn blower to low  
speed. A third time turns blower off. A built-in  
timer automatically turns blower off after  
20 minutes, unless manually deactivated first.  
The "Blower" indicator lights up  
when blower is on at high speed.  
It flashes when blower is on at low  
speed.  
Troubleshooting  
Automatic water heater start:  
When water temperature is 0.5˚C (1˚F) lower  
than the Set Point, the heater will automatically  
turn on until water temperature reaches Set  
Point plus 0.5˚C (1˚F).  
Pumps have started up for  
one minute on several  
occasions and "Filter Cycle"  
icon is flashing.  
Water temperature is  
displayed.  
3 flashing dots are  
displayed.  
The "Heater" indicator lights up when  
the heater is on. It flashes when there  
is a request for more heat but the heater  
has not yet started.  
Water temperature in  
the spa has reached 44˚C  
(112˚F).  
A problem has been detected.  
Not a bug but a feature!  
Do not enter the water!  
Check and open water  
valves. Clean filters if nec-  
essary. Check water level.  
Add water if needed.  
Note: The heater will not start if two pumps or  
more are running at high speed.  
Our Smart Winter Mode Do not enter the water!  
protects your system from  
the cold by automatically  
turning pumps on for one  
minute several times a day  
to prevent water from  
freezing in pipes.  
Allow water to cool down.  
The system will reset au-  
tomatically when water  
reaches 43˚C (109˚F).  
Setting water temperature:  
Use Up or Down arrow key to regulate water  
temperature. The temperature setting will be  
displayed for 5 seconds to confirm your new  
selection.  
Shut power off and power  
your spa up again to reset  
the system.  
Call your dealer or service  
supplier if problem persists.  
Call your dealer or service  
supplier if problem persists.  
The display is flashing.  
The "Set Point" symbol indicates the  
desired temperature, NOT the current  
water temperature!  
A power failure has  
occurred. Press any key  
to reset the system.  
Water temperature can be adjusted by 0.5˚C or  
1˚F increments from 15 to 40˚C (59 to 104˚F).  
 
Quick Reference Card  
K-4 keypad is mandatory when some options are selected. *  
Filter cycles  
Digital control pad lockout  
The system automatically performs 2 filter cycles per day, at 12-  
hour intervals. During a filter cycle, Pumps 2 & 3 and blower run  
for one minute. Pump 1 then runs at low speed for the remaining  
of the cycle and "Filter Cycle" icon lights up. (If system is equipped  
with a circulation pump, all pumps and blower run for one minute.  
Circulation pump then runs for the remaining of the cycle and  
"Filter Cycle" icon lights up.)  
This function allows you to prevent unauthorized parameter setting  
of the unit. This feature is especially helpful when young children  
have access to the keypad.  
There are two modes you can choose from: Full lock or Partial lock.  
Full lock means that all keypad functions are locked. Partial lock  
means that the basic functions of the spa will remain accessible  
(pumps, blower and light), but it will be impossible to change the  
temperature Set Point, to override the Economy mode or to  
enter the Programming mode.  
Setting filter cycles:  
1- Press Filter key.  
When control pad is locked, the "Lock" icon will be displayed.  
2- The display will show FDxx, with "xx"  
representing the duration in hours.  
FD10  
FS06  
Locking your digital control pad:  
3- Use Up and Down arrows to change setting.  
4- Press Filter key again.  
5- The display will show FSxx, with "xx"  
representing the delay before cycle starts.  
6- Use Up and Down arrows to change setting.  
7- Press Filter key to store settings.  
1- Press and hold Econo key for 5 seconds.  
2- The display will show LocP, with "P"  
representing Partial lock.  
LocP  
LocF  
3- Release key and keypad will be in Partial lock  
mode. Keep key pressed down for 5 more  
seconds if you want to be in Full lock mode.  
The "LocF" message will then be displayed.  
40-minute filter cycle time-out: If you turn a pump, blower or  
light on during a filter cycle, the cycle will be interrupted and will  
only resume 40 minutes after the system has turned the last active  
output off.  
When control pad is locked, all automatic functions of the system run  
as usual. If a key is pressed down, a "LocP" or "LocF" message will be  
displayed for 1 second. To unlock the keypad, simply press and hold  
Econo key again for 5 seconds.  
Purge cycles  
The system can perform a number of purge cycles per day.  
During a purge cycle, pumps and blower run for two minutes  
and "Filter Cycle" icon lights up.  
Economy mode  
To save energy, the Economy mode Set Point is 11˚C (20˚F)  
below the Normal mode Set Point.  
Setting purge cycles:  
The "Economy Mode" icon lights up when Economy  
mode is on.  
1- Press Filter key.  
2- The display will show P xx, with "xx"  
representing the currently set number of  
daily purge cycles.  
P 24  
Setting Economy mode:  
3- Use Up and Down arrows to change setting.  
4- Press Filter key to store settings.  
1- Press Econo key.  
2- The display will show EDxx, with "xx"  
representing the Economy mode duration.  
3- Use Up or Down key to change setting.  
4- Press Econo key again.  
ED12  
ES20  
Boost filtration mode  
5- The display will show ESxx, with "xx" representing  
the delay before mode starts.  
6- Use Up and Down arrows to change setting.  
7- Press Econo key a third time to store settings.  
This function allows you to speed up filtration after intensive use of  
your spa or to mix chemicals. Simply keep Pump 1 key pressed  
down for 5 seconds. Pump 1 will run at high speed for 45 minutes  
and "BOO" message will be displayed. Ozonator is also activated.  
40-minute Economy mode time-out: If you turn a pump, blower or  
light on while Economy mode is on, the Economy mode will be  
interrupted and will only resume 40 minutes after the system has  
turned the last active output off. The "Econ" message or "Economy  
Mode" icon will flash, depending on your system configuration.  
"CLE" message  
Every two weeks, the "CLE" message might be displayed indicating  
to clean the filter (depending on your spa configuration). Press any  
key to reset the message.  
Inverted display  
Press and hold Light key for 5 seconds to invert the display.  
If a power-up occurs, the display always returns to default mode.  
Real-time clock *  
Use Clock key to set real-time clock. The display toggles every  
5 seconds alternately showing the hourly time and the current  
water temperature.  
Summary of control panel parameters  
Water level sensor  
FDxx Filter cycle duration  
FSxx Filter cycle start delay  
LocX Control pad lockout  
EDxx Economy mode duration  
ESxx Economy mode delay  
P xx Purge cycles  
If the system is equipped with an optional water level sensor and the  
sensor detects an insufficient level of water in the tub, the system will  
prevent pumps from starting and will display the "H20" message.  
Pumps will be allowed to turn back on when water level returns  
above sensor.  
E
Smart  
Winter  
TM  
Mode  
 
9919-100614  

Closet Maid Outdoor Storage 12075 User Manual
Coleman Landscape Lighting 4D XPS User Manual
Curtis Water Dispenser FRP245 User Manual
CyberData Speaker 930095K User Manual
Desa Portable Generator RGH3000 User Manual
D Link Network Router DWM 152 User Manual
DXG Technology Camcorder DXG 202V User Manual
Foster Oven 7123040 User Manual
GBC Paper Shredder 4550X User Manual
Gefen Switch EXT HDMI13 244 User Manual