OPERATING MANUAL
ASSEMBLY
click
WASH FILTERS
click
Wash filters with cold water
at least every month.
REGISTER
YOUR FREE
5YEAR
GUARANTEE
TODAY
click
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THIS
MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
1.
This Dyson appliance is not intended for use by young children or infirm persons with reduced physical, sensory or
reasoning capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
by a responsible person concerning use of the appliance to ensure that they can use it safely.
Do not allow to be used as a toy. Close attention is necessary when used by or near children. Children should be
supervised to ensure that they do not play with the appliance.
2.
3.
Use only as described in this Dyson Operating Manual. Do not carry out any maintenance other than that shown in
this manual, or advised by the Dyson Helpline.
4.
5.
6.
Suitable for dry locations only. Do not use outdoors or on wet surfaces.
Do not handle any part of the plug or appliance with wet hands.
Do not use with a damaged cable or plug. If the supply cable is damaged it must be replaced by Dyson, its service
agent or similarly qualified persons in order to avoid a hazard.
7.
8.
9.
If the appliance is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors,
or dropped into water, do not use and contact the Dyson Helpline.
Contact the Dyson Helpline when service or repair is required. Do not disassemble the appliance as incorrect
reassembly may result in an electric shock or fire.
Do not stretch the cable or place the cable under strain. Keep the cable away from heated surfaces. Do not close a
door on the cable, or pull the cable around sharp edges or corners. Arrange the cable away from traffic areas and
where it will not be stepped on or tripped over. Do not run the appliance over the cable.
10. Do not unplug by pulling on the cable. To unplug, grasp the plug, not the cable. The use of an extension cable is not
recommended.
11.
Do not use to pick up water.
12. Do not use to pick up flammable or combustible liquids, such as petrol, or use in areas where they or their vapours
may be present.
13. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
14. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts, such as the brush
bar. Do not point the hose, wand or tools at your eyes or ears or put them in your mouth.
15. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything
that may reduce airflow.
16. Use only Dyson recommended accessories and replacement parts.
17.
18. Do not use without the clear bin and filters in place.
19. Do not leave the appliance when plugged in. Unplug when not in use and before servicing.
To avoid a tripping hazard rewind the cable when not in use.
20. Do not pull or carry by cable or use cable as a handle.
21. Use extra care when cleaning on stairs. Do not work with the appliance above you on the stairs.
22. Turn off all controls before unplugging. Unplug before connecting any tool or accessory.
READ AND SAVE THESE INSTRUCTIONS
THIS DYSON APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
Do not pull on
the cable.
Do not store near
heat sources.
Do not use near
naked flames.
Do not run over
the cable.
Do not pick up
water or liquids.
Do not pick up
burning objects.
Do not use above
you on the stairs.
Do not put hands
near the brush bar
when the appliance
is in use.
3
Storage
Operation
click
Emptying the clear bin
Looking for blockages
4
Carrying the appliance
Carpets or hard floors
Attachments
click
Brush bar – clearing obstructions
5
IMPORTANT!
WASH FILTERS
A
B
Base plate disassembly
6
Wash filters with cold water at least every month.
The filters may require more frequent washing if vacuuming fine dust.
click
click
click
click
click
Base plate reassembly
click
7
USING YOUR DYSON APPLIANCE
VACUUMING
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
CAUTION:
•
•
Do not use without the clear bin and filters in place.
Fine dust such as plaster dust or flour should only be vacuumed in very small
amounts.
Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimise any effect from this, do not put your hand or insert
any object into the clear bin unless you have first emptied it and rinsed it out with
cold water (see ‘Cleaning the clear bin’).
ASSEMBLY
Lie the appliance on its back.
•
•
•
•
Attach the cleaner head by sliding it on to the connections on the lower front part
of the ball. Ensure the electrical plug on the cleaner head fits into the twin-block
connection on the body of the appliance, which is directly above the airway.
Push firmly: the cleaner head will click into place.
Stand the appliance up straight.
Attach the wand handle by sliding it on to the top of the appliance. The spring
clip in the handle will click into place.
Ensure the hose is straight. Press the red button on the hose. Slide the wand into
the hose.
Ensure the hose and wand sit in the recess of the handle. Slide the end of the
wand down into the handle to secure it.
Close the wand cap.
Slide the tool holder onto the side of the duct as shown.
Ensure the cyclone and clear bin unit is secured to the main body of the
appliance.
Attach the tools as shown. In use, the tools can be attached to either the hose or
the wand.
Wind the cable anti-clockwise around the cable hooks. Secure with the clip.
To watch a short online video visit:
•
•
•
•
•
•
Powerful suction can cause the hose to ‘pull back’ – please take care.
Do not work with the appliance above you on the stairs.
Do not put the appliance on chairs, tables, etc.
•
•
Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
•
•
•
•
Do not leave the cleaner head in one place on delicate floors.
EMPTYING THE CLEAR BIN
•
•
•
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
Switch ‘OFF’ and unplug before emptying the clear bin.
To remove the cyclone and clear bin unit, press down on the red button at the
rear of the carrying handle on the cyclone.
•
•
•
•
•
To release the dirt, press all the way down on the red button at the rear of the
carrying handle on the cyclone.
To minimise dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
OPERATION
Unwind the cable.
•
•
•
Remove the clear bin carefully.
•
•
•
•
•
Seal the bag tightly, dispose as normal.
Plug the appliance into the mains electricity supply.
To switch ‘ON’ or ‘OFF’ press the power button, located as shown.
To use, recline the handle. The stabiliser stand will automatically lift up.
After use, return the appliance to the upright position, pushing it firmly into
place. The stabiliser wheels will automatically lower.
Then unplug the appliance, coil the cable safely and put the appliance away.
Switch ‘OFF’ the appliance, unplug and ensure it is upright before:
– changing or using tools
To refit:
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will
click into place
– ensure the cyclone and clear bin unit is secure.
•
•
•
CLEANING THE CLEAR BIN
– removing the hose or airway inspection parts.
Use the cyclone carry handle to carry the appliance.
•
•
Remove the cyclone and clear bin (instructions above).
To separate the cyclone unit from the clear bin press the red button to open
the clear bin base. This exposes a small silver button behind the red opening
mechanism. Press the silver button and separate the cyclone unit from the
clear bin.
•
ATTACHMENTS
To release the wand, open the wand cap and pull the red tube up and away from
the handle until it clicks into place.
Should you wish to use the hose without the wand, follow the above instruction
and press the red button to release the wand from the hose.
•
•
•
•
•
•
•
•
•
Clean the clear bin with cold water only.
Ensure the clear bin is completely dry before replacing.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Do not immerse the whole cyclone unit in water or pour water into the cyclones.
Clean the cyclone shroud with a dry cloth or dry brush to remove lint and dust.
To refit the bin to the cyclone unit:
– fit the cyclone shroud into the clear bin so that the silver button clicks and
engages
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance; it will
click into place
CARPETS OR HARD FLOORS
The brush bar will always default to ‘ON’ (spinning) each time you switch the
appliance ‘ON’ and recline it for cleaning.
The brush bar will not rotate when the appliance is upright.
To switch the brush bar off (e.g. for delicate rugs and hard floors):
– switch the appliance ‘ON’
•
•
•
– recline the appliance
– press the brush bar ‘ON/OFF’ button – the brush bar will stop spinning.
The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar –
clearing obstructions’.
Before vacuuming your flooring, rugs and carpets, check the manufacturer’s
recommended cleaning instructions.
Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming in ‘hard floor’ mode and consulting with
the flooring manufacturer.
The brush bar on the appliance may damage some carpet types. If you are
unsure, turn ‘OFF’ the brush bar.
– ensure the cyclone and clear bin unit is secure.
•
•
•
WASHING YOUR FILTERS
Your appliance has two washable filters, located as shown.
Check and wash the filters regularly according to instructions to maintain
performance.
Switch ‘OFF’ and unplug before checking or removing the filters.
The filters may require more frequent washing if vacuuming fine dust.
Wash with cold water only. Do not use detergents.
Do not put filters in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
•
•
•
•
•
•
•
LOOKING AFTER YOUR DYSON APPLIANCE
•
•
To remove filter A see the ‘Wash filters’ section in this Dyson Operating Manual.
After washing lay the filter on its side and leave at least 24 hours to dry
completely before refitting.
•
•
•
•
•
Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
Only use parts recommended by Dyson. If you do not this could invalidate
your guarantee.
•
To remove filter B:
– turn the central locking dial on the outer cover of the ball anti-clockwise until
the cover is released
– lift off the cover
– turn the filter one-quarter anti-clockwise to release.
Filter B should be rinsed and tapped out until the water runs clean, then tapped
out again to ensure all excess water is removed. Leave to dry completely for
24 hours.
It is normal for the filter in the ball to turn grey in colour.
To refit filter B:
Store the appliance indoors. Do not use or store it below 0°C. Ensure the
appliance is at room temperature before operating.
Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
If used in a garage, always wipe the base plate, ball and stabiliser wheels with
a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could
damage delicate floors.
•
•
•
– refit the filter on to the ball
– secure the filter by turning it one-quarter turn clockwise.
When refitting the outer cover of the ball, keep turning the central locking dial
clockwise. When it starts to click it is locked.
•
•
To watch a short online video visit:
8
LOOKING FOR BLOCKAGES
PLEASE REGISTER AS A DYSON APPLIANCE OWNER
•
Switch ‘OFF’ and unplug before looking for blockages. Failure to do so could
result in personal injury.
To help us ensure you receive prompt and efficient service, please register as a
Dyson appliance owner. There are three ways to do this:
Telephone the Dyson Helpline.
•
•
Look for blockages in the wand, airways and cleaner head.
To remove the base plate to access an obstruction, see ‘Base plate –
disassembly/reassembly.
To look for blockages in the airway between the ball and the cleaner head
you will need to remove the cleaner head: see ‘Base plate – disassembly/
reassembly’.
•
•
•
Complete the enclosed form and post it to us.
This will confirm ownership of your Dyson appliance in the event of an insurance
loss, and enable us to contact you if necessary.
•
•
•
•
Beware of sharp objects when checking for blockages.
Refit all parts securely before using.
Clearing blockages is not covered by your guarantee.
LIMITED 5 YEAR GUARANTEE
TERMS AND CONDITIONS OF THE DYSON 5 YEAR LIMITED GUARANTEE
WHAT IS COVERED
CLEARING BLOCKAGES – THERMAL CUT-OUT
•
•
The repair or replacement of your Dyson appliance (at Dyson’s discretion) if it
is found to be defective due to faulty materials, workmanship or function within
5 years of purchase or delivery (if any part is no longer available or out of
manufacture Dyson will replace it with a functional replacement part).
Use of the Dyson appliance in the country of purchase only.
•
•
This appliance is fitted with an automatically resetting thermal cut-out.
Large items may block the tools or wand inlet. If any part becomes blocked the
appliance may overheat and automatically cut-out.
Switch ‘OFF’ and unplug. Leave to cool down for 1-2 hours before checking
filters or for blockages.
•
•
•
Clear any blockage before restarting.
Clearing blockages is not covered by your guarantee.
WHAT IS NOT COVERED
Dyson does not guarantee the repair or replacement of a product as a result of:
Accidental damage, faults caused by negligent use or care, misuse, neglect,
careless operation or handling of the appliance which is not in accordance with
the Dyson Operating Manual.
BRUSH BAR – CLEARING OBSTRUCTIONS
If your brush bar is obstructed, it may shut off. If this happens, you will need to
remove the blockage.
Switch ‘OFF’ and unplug before proceeding. Failure to do so could result in
personal injury.
Beware of sharp objects when clearing obstructions.
If you still cannot clear the obstruction, please follow the instructions below to
remove the base plate. This gives more access to the obstruction. Alternatively,
contact a Dyson expert on the Dyson Helpline or visit the website. Clearing
brush bar obstructions is not covered by your guarantee.
•
•
•
•
•
Use of the appliance for anything other than normal domestic household
purposes.
Use of parts not assembled or installed of accordance with the instructions of
Dyson.
Use of parts and accessories which are not genuine Dyson components.
Faulty installation (except where installed by Dyson).
Repairs or alterations carried out by parties other than Dyson or its authorised
agents.
Blockages – please refer to the Dyson Operating Manual for details of how to
look for and clear blockages.
•
•
•
•
•
•
BASE PLATE – DISASSEMBLY/REASSEMBLY
•
Switch ‘OFF’ and unplug before proceeding. Failure to do so could result in
personal injury.
•
•
Normal wear and tear (e.g. fuse, brush bar, etc).
If you are in any doubt as to what is covered by your guarantee, please contact
Dyson.
•
•
Lie the appliance on its front.
Detach the red ‘C’ clip which is on the connection between the cleaner head
and the appliance. It is quite firm, but do not pull it off roughly. Use a constant,
firm pressure.
SUMMARY OF COVER
The guarantee becomes effective at the date of purchase (or the date of delivery
if this is later).
You must provide proof of (both the original and any subsequent) delivery/
purchase before any work can be carried out on your Dyson appliance. Without
this proof, any work carried out will be chargeable. Keep your receipt or
delivery note.
All work will be carried out by Dyson or its authorised agents.
Any parts which are replaced will become the property of Dyson.
The repair or replacement of your Dyson appliance under guarantee will not
extend the period of guarantee.
•
•
•
•
Pull the cleaner head away from the appliance. Use a constant, firm pressure.
At each end of the cleaner head are two levers:
– swing them out at right angles
– the base plate will disengage
– lift up the top edge, so it rotates to the upright position
– lift out.
Beware of sharp objects when clearing obstructions.
To refit the base plate:
– fit the 3 lugs on the lower edge of the base plate into the 3 slots in the base of
the cleaner head
– swing the upper edge of the base plate down; it will click into place.
To secure the base plate push both levers back into position so they are flush
with the surface of the cleaner head.
Refit the red ‘C ‘clip onto the cleaner head. The flatter edge of the clip fits
against the cleaner head. It is easier to slide one lug into its slot before the other.
Lie the appliance on its back.
•
•
•
•
•
•
The guarantee provides benefits which are additional to and do not affect your
statutory rights as a consumer.
•
•
ABOUT YOUR PRIVACY
Your information will be held by Dyson Limited and its agents for promotional,
marketing and servicing purposes.
If your personal details change, if you change your mind about any of your
marketing preferences or if you have any queries about how we use your
information, please contact Dyson Limited.
For more information on how we protect your privacy, please see our privacy
policy on the Dyson website.
•
•
•
•
Attach the cleaner head by sliding it on to the connections on the lower front
part of the ball. Ensure the electrical plug on the cleaner head fits into the
twin-block connection on the body of the appliance, which is directly above the
airway. Push firmly: the cleaner head will click into place.
•
BRUSH BAR – TROUBLESHOOTING
If the brush bar has stopped spinning, follow the instructions above on clearing
obstructions. Alternatively, contact a Dyson expert on the Dyson Helpline or visit
the website.
To watch a short online video visit:
•
•
DYSON CONTACT DETAILS
UK:
Dyson Helpline: UK: 0800 298 0298
Open 7am–10pm. 7 days a week.
Email: askdyson@dyson.co.uk
Address: Dyson Limited, Tetbury Hill, Malmesbury, Wiltshire SN16 0RP England.
ROI:
Dyson Helpline: ROI: 01 475 7109
Open 7am–10pm. 7 days a week.
Email: askdyson@dyson.co.uk
DISPOSAL INFORMATION
Dyson products are made from high grade recyclable materials. Please dispose
of this product responsibly and recycle where possible.
GUARANTEE TERMS & CONDITIONS
DYSON CUSTOMER CARE
THANK YOU FOR CHOOSING TO BUY A DYSON APPLIANCE
After registering your free 5 year guarantee, your Dyson appliance will be
covered for parts and labour for 5 years from the date of purchase, subject to
the terms of the guarantee.
Address: Unit 10, Grants Lane, Greenogue Business Park, Rathcoole, Dublin 24.
PRODUCT INFORMATION
Please note: Small details may vary from those shown.
If you have any questions about your Dyson appliance, call the Dyson Helpline
with your serial number and details of where/when you bought the appliance.
Most questions can be solved over the phone by one of our trained Dyson
Helpline staff.
for online help, general tips and useful information about Dyson.
If your Dyson appliance needs a service, call the Dyson Helpline so we can
discuss the available options. If your Dyson appliance is under guarantee, and
the repair is covered, it will be repaired at no cost.
Your serial number can be found on your rating plate which is behind the
clear bin.
9
IMPORTANT!
WASH FILTERS
Wash filters with cold water at least every month.
The filters may require more frequent washing if vacuuming fine dust.
Dyson Customer Care
After registering your free 5 year guarantee, your Dyson
appliance will be covered for parts and labour for 5 years from
the date of purchase, subject to the terms of the guarantee.If you
have any questions about your Dyson appliance, call the Dyson
Helpline with your serial number and details of where/when you
bought the appliance. Most questions can be solved over the
phone by one of our trained Dyson Helpline staff.
DYSON CONTACT DETAILS
UK:
Website: www.dyson.co.uk/support
Dyson Helpline: UK: 0800 298 0298
Open 7am–10pm. 7 days a week.
Email: askdyson@dyson.co.uk
Address: Dyson Limited, Tetbury Hill, Malmesbury, Wiltshire SN16 0RP England.
ROI:
Website: www.dyson.ie/support
Dyson Helpline: ROI: 01 475 7109
Open 7am–10pm. 7 days a week.
Email: askdyson@dyson.co.uk
Address: Unit 10, Grants Lane, Greenogue Business Park, Rathcoole, Dublin 24.
www.dyson.com
JN.44809 PN.23481-04-02 16.11.11
GUARANTEE FORM
Serial number
Date of purchase
Title
Country of purchase
UK
ROI
//
Surname
First name
Address
Postcode
email
Telephone
Mobile
As a Dyson appliance owner, you can hear about
Dyson inventions, services and products before anyone
else. If it’s okay to contact you, please let us know how
we may do this.
We sometimes ask other companies (such as market researchers) to
contact owners on our behalf. We do this to get feedback on ideas or
ask you to try new products and services. Would this be okay?
Yes
No
By mail
Yes
Yes
Yes
Yes
No
No
No
No
By phone
By email
By text message
3 EASY WAYS TO REGISTER YOUR FREE 5 YEAR GUARANTEE
REGISTER
REGISTER
REGISTER
ONLINE
BY PHONE
BY MAIL
Visit our website to register
your full parts and labour
guarantee online.
Call our dedicated Helpline.
Open 7am–10pm.
7 days a week.
Complete and return
the form to Dyson in the
envelope supplied.
UK 0800 298 0298
ROI 01 475 7109
|
Continental Electric Refrigerator CECR61431 User Manual
Craftsman Air Compressor 91972458 User Manual
Crate Amplifiers Musical Instrument Amplifier GX 120 212+ User Manual
Cub Cadet Lawn Mower 24HP Tank 53AB5ETW150 19HP Tank 53BB5Dav150 20HP 53AB5E6V150 25 HP Tank 53AB5D8X150 27 HP Tank 53AB5BDX150 28 HP Tank 53AB5FEZ150 User Manual
Curtis Home Theater System DVD1073 User Manual
Danby Refrigerator DAR194BL User Manual
Dymo Printer 350D User Manual
Estate Refrigerator 2318600 User Manual
Franklin Industries LLC Beverage Dispenser FCW20T User Manual
Gateway Computer Monitor VX730 User Manual