Edelbrock Camera Accessories 65732 User Manual

Shorty Headers  
For 2000-2002 Camaro/Firebird  
5.7L LS1 V8, Auto/Manual Transmission  
Catalog #65732 & #65733  
®
INSTALLATION INSTRUCTIONS  
Please study these instructions carefully before installing your new Tubular Exhaust System. If you have any questions, please contact  
our Technical Hotline at : 1-800-416-8628 from 7 am – 5 pm, Monday through Friday, Pacific Standard Time or e-mail us at  
DESCRIPTION: These shorty headers are designed to improve the exhaust efficiency of the GM 5.7 Liter LS1 V8 engine. This system  
does not require welding for installation and retains all O.E.M. emissions equipment.  
IMPORTANT NOTE:  
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in  
poor performance and engine or vehicle damage.  
Suggested tools needed for installation: This vehicle has some metric fasteners.  
1/4” ratchet and socket set  
3/8” ratchet socket set with extensions and universal 13mm and 15mm swivel sockets  
Combination of open-end wrenches  
Jackstands, screwdrivers, pliers, crescent wrench, etc.  
Liquid penetrant (GM #1052627 or equivalent); anti-seize compound (GM #5613695 or equivalent)  
SPECIAL NOTICE: This Edelbrock part has received an Executive Order number (E.O. #) from the California Air Resources Board  
(C.A.R.B.) making it legal for street use on pollution-controlled motor vehicles in all 50 states. To assist you with emissions equipment  
certification, we have included a silver fan shroud decal to help testing personnel verify that this part is a legal replacement part on  
the vehicle for which it is cataloged. The adhesive-backed decal should be affixed to your fan shroud next to the existing emission  
and engine specification decal. Do not cover your original equipment specification decal with the Edelbrock fan shroud decal.  
WARNING: The use of “Thermal Wrap” or any aftermarket coating process will void the warranty on your Tubular Exhaust System.  
Those products can cause excessive heat and moisture build up resulting in corrosion and early failure of the system.  
INSTALLATION INSTRUCTIONS  
LEFT SIDE  
1. Disconnect and remove spark plug wires.  
DISASSEMBLY:  
1. Disconnect negative battery cable.  
2. Disconnect A.I.R. assembly from stock manifold.  
3. Remove manifold bolts.  
2. Raise vehicle and unplug all 02 sensors and carefully  
remove.  
4. Remove manifold from below.  
3. Starting with the driver’s side, remove the three bolts  
on the inlet flange of the catalytic converter.  
4. At mid-section of left side exhaust pipe is a two-bolt  
flange; unbolt and set catalytic converter aside.  
5. On passenger’s side, remove the three bolts on the  
inlet flange of the catalytic converter.  
5. Install flange gasket and one 8mm bolt, lock washer,  
and flat washer at rear most bolthole (leave bolt  
loose enough to accept header).  
6. Place header into position from below. Start all bolts  
and washers, then tighten evenly starting with  
centermost bolts.  
6. At mid-section of exhaust pipe is a two-bolt flange,  
unbolt and set catalytic converter assembly aside.  
Note: Use flat washers and lock washers on all bolts.  
©2006 Edelbrock Corporation  
Catalog #65732 & #65733  
Brochure #63-0405  
Rev. 7/06  
Page 1 of 2  
 

Clarion Car Video System HRM100 User Manual
Coleman Indoor Fireplace 5059 720 User Manual
Control4 Home Theater Server HC 300 User Manual
Crosley Clothes Dryer 134856200 User Manual
Crosley Clothes Dryer 134993900A User Manual
Cub Cadet Lawn Mower 108 User Manual
Electro Voice IP Phone ENG 618 User Manual
Euro Pro Iron EP8020 User Manual
Gitzo Camcorder Accessories G1515 User Manual
Gitzo Camcorder Accessories GM3550 User Manual