Fortinet Network Card ADM FB8 User Manual

LED  
State  
Description  
Blue  
Ejection latch open.  
HS  
Flashing Blue  
Ejection latch opened during system operation.  
LED currently not in use.  
OOS  
PWR  
OT  
Amber  
Off  
The module is properly inserted in the FortiGate unit.  
The module is not receiving power from the FortiGate unit.  
LED currently not in use.  
HS  
OOS  
PWR  
OT  
Green  
Off  
The correct cable is in use and the connected equipment has power.  
No link established.  
LINK  
1
2
3
4
5
6
7
8
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ADM-FB8  
Flashing Amber Network activity at this interface.  
Off No network activity at this interface.  
ACT  
FortiGate-ADM-FB8  
© Copyright 2008 Fortinet Incorporated. All rights reserved.  
Products mentioned in this document are trademarks or registered trade-  
marks of their respective holders.  
Regulatory Compliance  
FCC Class A Part 15 CSA/CUS  
10 January 2008  
01-30005-0437-20080110  
Checking the Package Contents  
Connector  
Type  
Speed  
Protocol Description  
Ports 1 to 8  
SFP Fiber  
1000 Mb  
Ethernet Fiber network connections.  
Q u i c k S t a r t G u i d e  
HS  
OOS  
PWR  
HS  
OT  
1
2
3
4
5
6
7
8
OOS  
PWR  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ADM-FB8  
OT  
FortiGate-ADM-FB8  
1
2
3
4
5
6
7
8
Copyright 2007 Fortinet Incorporated. All rights reserved.  
Trademarks  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
ACT  
LINK  
Products mentioned in this document are trademarks.  
ADM-FB8  
x4 SFP Transceivers  
QuickStart Guide  
Installing the transceivers  
The FortiGate ADM-FB8 module ships with four SFP transceivers that you must install for nor-  
mal operation of the FortiGate ADM-FB8 module. The SFP transceivers are inserted into cage  
sockets numbered 1 through 8 on the FortiGate ADM-FB8 front panel. You can install the SFP  
transceivers before or after inserting the FortiGate ADM-FB8 module into a FortiGate unit.  
If the transceiver does not easily slide in and click into place, it may not be aligned correctly  
or may be upside down. If this happens, remove the SFP transceiver, realign it or rotate it  
and slide it in again.  
To Install the transceivers  
To complete this procedure, you need:  
• A FortiGate- ADM-FB8 module  
1. Remove the caps from SFP cage sockets on the FortiGate ADM-FB8 front panel.  
• SFP transceivers  
To avoid any electrostatic discharge, install in a static free area.  
2. Hold the sides of the SFP transceiver and slide SFP transceiver into the cage socket  
until it clicks into place.  
FortiGate ADM-FB8 modules must be protected from static discharge and physical shock.  
Only handle or work with FortiGate ADM-FB8 modules at a static-free workstation.  
Handling the SFP transceivers by holding the release latch can damage the connector.  
Do not force the SFP transceivers into the cage slots.  
Installing the AMC module  
The module should glide smoothly into the chassis. If you encounter any resistance while  
sliding the module in, the module could be aligned incorrectly. Pull the module back out  
and try inserting it again.  
It is important to carefully seat the FortiGate ADM-FB8 module all the way into the chassis.  
Only then will the FortiGate ADM-FB8 module power-on and start up correctly.  
To complete this procedure, you need:  
8. Press the hot swap latch firmly to lock in the module.  
9. Power on the FortiGate unit. The hot swap (HS) LED turns on and then begins flashing.  
• A FortiGate ADM-FB8 module  
• A FortiGate chassis with an empty AMC double-width (DW) opening.  
To avoid any electrostatic discharge, install in a static free area.  
ASM-FB8 module ports  
AMC/1  
AMC/3  
AMC/5  
AMC/7  
IP:  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
AMC/2  
AMC/4  
AMC/6  
AMC/8  
IP:  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
FortiGate ADM-FB8 modules are not hot swappable. The procedure for inserting the  
FortiGate ADM-FB8 module into a FortiGate chassis slot requires the FortiGate unit to be  
powered off.  
Netmask:  
IP:  
Netmask:  
IP:  
Netmask:  
IP:  
Netmask:  
IP:  
FortiGate ADM-FB8 modules must be protected from static discharge and physical shock.  
Only handle or work with FortiGate ADM-FB8 modules at a static-free workstation.  
Netmask:  
IP:  
Netmask:  
IP:  
To insert a FortiGate ADM-FB8 module into a FortiGate chassis  
Netmask:  
Netmask:  
1. Ensure the FortiGate unit is powered off before proceeding.  
Removing the AMC module  
2. Attach an ESD wrist or ankle strap to your wrist or ankle and to an ESD socket or to a  
bare metal surface on the chassis or frame.  
Should you need to remove the ADM-FB8, shut down the FortiGate unit using proper shut  
down procedures.  
3. Remove the panel block on the FortiGate unit using the hot swap latch.  
4. Insert the FortiGate ADM-FB8 module into the empty slot in the chassis. Ensure the  
Fortinet logo is right-side up. It should be on the upper-right corner of the module  
To remove the ADM-FB8 module  
5. Carefully guide the module into the chassis.  
1. Ensure the FortiGate unit is powered off before proceeding.  
6. Pull out the hot swap latch on the right-hand side of the module to the extended position  
if it is pushed in.  
2. To avoid any electrostatic discharge (ESD) when handling FortiGate ASM-FB8 modules,  
install in a static free area.  
7. Insert the module by applying moderate force to the front faceplate near the upper edge  
to slide the module into the slot.  
3. Pull the hot swap latch on the right-hand side of the module to the extended position to  
unlock the module from the FortiGate unit.  
4. Gently pull the hot swap latch to remove the module.  
 

Coleman Tent 2000008054 User Manual
Conair Hair Dryer BC178BCRW User Manual
Craftsman Lawn Mower 917270841 User Manual
Cuisinart Toaster CGR SMC User Manual
Cypress Computer Hardware STK17TA8 User Manual
Dynex Modem 2300 0248 User Manual
Earthquake Sound Speaker SWS 10X 4 OHM User Manual
Electro Voice Speaker System EVF 1122S 66 User Manual
EverFocus Car Video System EN 7517E User Manual
Gitzo Camcorder Accessories GT3541LS User Manual