Euro Pro Vacuum Cleaner UV647H User Manual

3 Speed Cordless Sweeper  
OWNER’S MANUAL  
Model: UV647H  
8.4 Volt DC  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
Tel. : 1 (800) 798-7398  
 
Care and Maintenance  
To improve the performance and life of your unit, we recommend you do the  
following:  
1. Once a month clean the unit with a dry cloth, including the chamber which the  
dust container fits into. Remove any hair, fiber or other materials that may have  
built up in the chamber, on the rotating brush or edging tool.  
2. Don’t use abrasive materials to clean the sweeper. Do not immerse the unit in  
water.  
Model: UV647H  
8.4 Volt DC  
3. Do not pick up liquids or use on wet floors.  
4. Do not use on concrete, tar or similar rough surfaces .  
5. Don’t pick up pieces of string or fabrics with the sweeper.  
6. Do not clean tasseled or frayed carpets with the sweeper.  
7. Any other servicing should be done by an authorized service representative.  
TROUBLESHOOTING GUIDE  
PROBLEM  
POSSIBLE REASON  
POSSIBLE SOLUTION  
1. Batteries discharged.  
2. No power in electrical  
outlet supplying charging  
adapter.  
1. Charge unit.  
SWEEPER WILL NOT  
OPERATE  
2. Check fuse or breaker.  
Replace fuse/reset breaker.  
3. Call Customer Service.  
3. Unit needs servicing.  
SWEEPER WILL NOT  
PICK-UP  
1. Dust container is full.  
2. Unit needs recharging.  
1. Empty dust container.  
2. Charge unit.  
DUST ESCAPING  
FROM SWEEPER  
1. Dust container is full.  
1. Empty dust container.  
1. Check for excessive material  
on brush or in bottom of  
sweeper. Remove obstruction  
from brushes and/or sweeper.  
2. Empty and clean dust  
container.  
ROTATING BRUSH  
WILL NOT PICK UP  
1. Unit clogged.  
2. Dust container is full.  
1. Sweeper Power Head  
10. Dust Cup (Container)  
11. Charging Jack  
12. Lower Handle  
13. Extension Tube  
14. Telescopic Tube  
15. Upper Handle  
2. On / Off Switch  
3. Speed Control  
4. Speed Indicator Lights  
5. Charging Indicator Light  
6. Rotating Brush  
7. Brush Cover  
1. Electrical outlet not  
working  
2. Charging Adapter not  
working  
1. Check to ensure outlet is  
working properly. (Easily  
checked by plugging in  
SWEEPER WILL NOT  
CHARGE  
another appliance.  
3. Batteries no longer  
functioning  
2. Replace charging adapter  
3. See battery disposal pg. 8.  
16. Charging Adapter: Use Only  
AD-1215-U8  
8. Edging Tool  
9. Gear box  
Illustrations may differ from actual product.  
NOTE: Cordless Sweeper Model UV647H is shipped with the  
batteries uncharged. Charging of the unit for 20 hours  
prior to first use is required. Use replacement battery  
# XB617U only.  
9
2
 
Assembling Your Cordless Sweeper  
Battery Removal & Disposal  
Before you start:  
NOTE: If uncertain as to how to remove your battery pack, we suggest you take  
your sweeper to a reputable small appliance service technician to have this  
service performed.  
Your Cordless Sweeper will require very little assembly. You should remove it from the  
carton and familiarize yourself with all the components listed per the exploded view  
drawing (pg.2) This will help you in the assembly and operation of your cordless  
sweeper.  
Follow these steps when battery removal is required.  
Note: The charging adapter is shipped inside the dust cup.  
This sweeper is equipped with Ni-Cd batteries and you need to dispose of them  
properly. When the batteries are no longer good for use, they must be removed from  
the sweeper for disposal. Do not remove the batteries for any reason other than  
disposal of them. The batteries must be recycled or disposed of in accordance  
with local regulations. Please consult your Yellow Pages or local recycling  
center for more information.  
WARNING: You must never use ordinary batteries for replacement as these  
may leak and cause damage. Use only battery pack XB617U  
for replacement.  
Fig. 2  
Fig. 1  
1. In the event that the edging tool is not attached to the sweeper, insert the edging  
tool into the "square" hole under the bottom of the sweeper power head. Gently  
but firmly push until the edging tool locks into place. (Fig. 1)  
2. Insert the lower handle. Fasten it with the captive nut and bolt that is  
provided. (Fig. 2)  
3. Attach the telescopic tube to the extension tube  
by pushing the plastic insert into  
Removal of Battery Pack  
1. Remove the extention handle and dust cup container.  
2. Turn unit over so that the base is facing upwards. Be careful not to turn the unit  
ON. (Fig. 17)  
3. Push in locking tab and lift off battery assembly. (Fig. 18)  
4. Place battery assembly aside.  
5. Insert the new battery assembly into unit. Ensure that locking tab snaps in place.  
the bottom part of the telescopic pole.  
(Fig. 3a) Push in until the "tab" on the  
plastic insert snaps into the open  
slot on the telescopic tube.  
Push the telescopic tube  
into the upper handle. (Fig. 3)  
Insert the extension tube into the  
CAUTION: This appliance contains Ni-Cd batteries. The batteries must  
be recycled or disposed of in accordance with local  
regulations. Please consult your Yellow Pages or local  
recycling center for more information.  
lower handle firmly in place. (Fig. 3b)  
4. Place the handle into the upward  
storage position.  
5. Plug the charging adapter into the  
Fig. 3a  
sweeper power head charging jack.  
Fig. 3b  
Plug the charging adapter cord  
into a standard electrical outlet  
(120V, 60Hz.) The green charging  
indicator should illuminate. If it does  
not, depress the On/Off switch one  
Fig. 3  
time.  
Fig. 17  
Fig. 18  
CAUTION: ALWAYS USE ADAPTOR SUPPLIED (ONLY)  
WITH SWEEPER  
8
3
 
Changing the Rotating Brush, Gear Box & Squeegee  
How to Operate Your Cordless Sweeper  
1. Before using, please ensure that the cordless sweeper has been initially  
charged for 20 hours  
WARNING:Use caution when changing the rotating brush and gear box  
so that the unit does not turn ON when pressing down on the sweeper  
power head.  
Your cordless sweeper will only operate properly when the batteries are fully  
charged. Your sweeper will operate for varying lengths of time on a full charge.  
This will depend upon the type of surface being cleaned. (Longer operating time on  
bare floors vs carpets.)  
1. Remove the extension tube handle from the sweeper power head.  
2. Turn sweeper power head upside down being careful Not to accidentally turn the  
unit ON.  
2. Push the On/Off switch to operate the unit. To turn off, press switch again.(Fig.4)  
3. Remove the brush cover. (Fig. 10) (Refer to page 5 for detailed instructions.)  
4. Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 11 & 12)  
5. Lift the brush bar end cap up from the slot. (Fig. 13)  
6. Pull the brush bar out of the bushing and slip off the belt to remove the brush bar.  
(Fig. 14)  
"On/Off" switch  
7. Insert the new brush bar by first inserting the brush bar into the bushing on the end  
opposite the driver belt. (Fig. 14)  
8. Slip the belt over the brush bar cap.  
9. Insert the brush bar into the slot. (Fig. 13)  
Fig. 4  
10.Insert the gear box tabs into the tab slots and push down until it clicks into place.  
11.To replace the squeegee, follow instructions above for removing the gear box and  
slide the squeegee out from left to right. (Fig. 15)  
CAUTION: Any electronic or electrical appliance should not be  
Locking  
tab  
Gear box  
Lift  
stored in or exposed to areas of high heat or humidity. Do  
not store your cordless sweeper close to stoves,  
radiators, furnaces or in a bathroom or bathing area.  
3. To release the handle to a comfortable position, apply pressure to the top of  
the sweeper head with your foot while pulling back on the handle.(Fig. 5)  
Fig. 11  
Fig. 10  
Fig. 12  
Gear box tabs  
Slide  
Fig. 13  
Fig. 15  
Fig. 14  
Changing the Belt  
If you find that the belt has broken and it needs replacing:  
1. Remove the brush cover. (Fig. 10)  
2. Push in on the locking tab of the gear box and lift gear box  
to remove. (Fig. 11 & 12).  
3. Push in on the locking tab of the belt access panel and lift  
off to remove. (Fig. 16)  
Fig. 5  
4. Using a pair of tweezers, remove any leftover bits of the  
belt that might still be there.  
4. To change the speed of the sweeper, press on the speed control button. As you  
press on it, the speed indicator light will change. If one light lights up, then you  
have the low speed; two lights, medium speed; three lights, high speed.  
5. If something were to jam or overload the brush bar system, the units speed  
indicators will flash and the unit will stop operating, this is normal. To reset the  
unit, remove the tangled object and then depress the on/off switch once and  
then depress it again to restart the unit.  
Fig. 16  
5. Pull the brush bar out of the bushing. (Fig. 13)  
6. Using a new belt, insert it into the opening until it is in all the way.  
7. Using a pair of tweezers, insert them into the belt access panel and lift the new belt  
over the back gear.  
8. Slide the belt over the brush bar cap and then insert the brush bar into the slot.  
(Fig. 13)  
9. Insert the gear box tabs into the tab slots and push down until it clicks into place.  
10. Press the belt access panel down until it snaps in place.  
11. Replace the brush cover (Fig. 10)  
4
7
 
Cleaning the Dust Container  
To achieve the best performance, empty the dust container after each use.  
2. When first started, the sweeper will start in the highest speed to prevent  
overloading the unit when starting on heavy carpets. Other speeds can then be  
selected by depressing the speed selector switch.  
3. For best cleaning performance, use low speed on hard surfaces, medium speed  
on low carpets/rugs, and use high speed on deeper carpets. These are guide  
lines and you will find the optimum speed settings for your surfaces and debris to  
be picked up through use and experience.  
4. The sweeper will automatically try to maintain speeds on all surfaces. The unit  
may appear to be pulsing during use to maintain it’s speed, this is normal. If this  
occurs, please select the next highest speed to gain optimum performance.  
5. To protect your sweeper and it’s components, the sweeper is provided with an  
electronic overload circuit. If something were to jam or overload the brush bar  
system, the units speed indicators will flash and the unit will stop operating, this  
is normal. To reset the unit, remove the tangled object and then depress the  
on/off switch once and then depress it again to restart the unit.  
3. Replace dust container on cordless  
sweeper.  
1. Pull the dust  
container straight  
out from the side.  
(Fig. 6)  
4. Periodically remove the brush cover on  
the front of the cordless sweeper and  
remove any build up of lint, hair or fiber  
on the rotating brush. To remove the  
cover - grip the cover from the bottom,  
pull out and  
upward until the  
cover unlocks  
from the side  
slots and tabs  
Fig. 6  
2. Empty dust  
container contents.  
(Fig. 7) If desired-  
you may rinse with  
water to clean the  
dust container –  
but dry thoroughly  
before replacing on  
the sweeper.  
located on the  
top of the  
sweeper. (Fig. 8)  
Fig. 7  
Fig. 8  
NOTE: If, when you place the sweeper to recharge and the charging indicator  
light does NOT illuminate, then press the On/Off button once to turn the  
sweeper off. The charging indicator light should now light up.  
CAUTION: Do not accidentally turn unit on while cleaning. Do not clean  
while unit is charging.  
NOTE: Peak performance may only be realized after the unit has been  
charged and discharged two (2) or three (3) times.  
Charging the Cordless Sweeper  
1. Connect the charger plug to the charging jack or hole on the back of the  
sweeper. Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only  
Charger AD-1215-U8. (Fig. 9)  
2. This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must be  
charged for a minimum of 20 hours.  
IMPORTANT: To maintain peak performance of your cordless sweeper, it is  
recommended that the unit be fully discharged, then  
completely re-charged once a month.  
3. When recharging the unit, the "On/Off" switch  
must be in the "OFF" position.  
CAUTION  
4. The charging light indicator on the top of the  
sweeper will turn solid green to indicate that the  
sweeper is properly charging.  
Use only with the battery pack supplied with the unit. (Item # XB617U)  
Do not attempt to remove the battery pack from the unit to charge it.  
Never attempt to throw the battery pack or unit into a fire or incinerate it.  
Do not attempt to remove or damage the battery casing.  
Battery must be recycled or disposed of in accordance with local  
regulations at the end of it's service life. Please consult your Yellow Pages  
or local recycling center for more information.  
5. To recharge, repeat step #1 above. Charging  
times will vary depending upon the amount  
of usage between charging cycles.  
Fig. 9  
Note: Your sweeper is highly advanced and has electronic controls that optimize the  
cleaning ability and durability of the sweeper. Please review the following instructions  
carefully to ensure that all features are utilized for best performance.  
STORING THE CORDLESS SWEEPER  
1. When running the unit, the battery indicator will start as solid green, change to solid  
red when approximately 70% of the battery life is used, and flash red when  
in need of charging. The sweeper will prevent the batteries from being deeply  
discharged and will indicate this by the speed indicators flashing and the sweeper  
will stop operating. This is normal and all that needs to be done is to recharge the  
sweeper fully. The speed indicator lights will stop flashing only after the “On/Off”  
switch is set to the “Off” position. When recharging from being fully discharged, the  
unit must charge for 1 hour minimum before it’s electronics will allow the unit to  
operate again.  
Your cordless sweeper may be stored by using the slot on the back of the upper  
handle and hanging it from a screw secured to a wall or other vertical surface. Use  
a #6 flat or pan head screw with the appropriate hardware for the surface that the  
sweeper will be mounted on, (i.e. gyproc). Allow the screw head to extend a  
approximately 3/16" from the mounting surface. Always empty your sweeper before  
hanging up for storage. NOTE: Always empty the sweeper dust cup before storing.  
5
6
 

Electro Voice Music Mixer MA 1212 User Manual
Everpure Water System 4CB5 S User Manual
Excalibur electronic Home Safety Product H522 User Manual
Extron electronic Speaker CS 120P User Manual
Fisher Price Doll 79538 User Manual
FujiFilm Camcorder 16229490 User Manual
Fujitsu Scanner fi 4750L User Manual
Garmin Home Safety Product GWS 10 User Manual
GE Camera Accessories UV 1 User Manual
Gigabyte Computer Accessories GZ FSCA1 AN User Manual