Foundations Baby Furniture 100 SSE User Manual

Model 100-SSE  
Special Needs Extended Length Changing Station  
Installation Instructions  
Thank you for purchasing a quality Foundations® product. Our goal is 100% consumer satisfaction!  
If, for any reason you are not satisfied or if you have questions regarding your product or installation,  
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor  
or reseller as we are better prepared to assist you.  
WARNING  
Failure to follow these warnings and the installation instructions could result in serious injury  
or death.  
Read all instructions before installing the extended length changing station. Keep these  
instructions. DO NOT discard.  
SI257F  
 
INSTALLATION - RECESSED  
NOTE: If installing a surface-mount changing station,  
63 1/4"  
see “Installation - Surface-Mount” section.  
1"  
(1607 mm)  
(25.4 mm)  
TOP  
VIEW  
3 7/8"  
(98.4 mm)  
Recommended Blocking:  
Wood double stud blocking is necessary. Contact an architect and  
building official to make sure the blocking is adequate and complies  
with building codes (Fig. b).  
63 1/4" (1607 mm)  
Rough-in  
Double Stud  
For A. D. A. compliance, top of lower double stud MUST be 27“  
FRONT  
VIEW  
21 3/4"  
(552 mm)  
Rough-in  
(68.5 cm) from the floor.  
19.4"  
(492 mm)  
1. Slide changer into blocking area and mark mounting hole location  
on blocking studs.  
HINT: This may require 2 additional people to help hold changer  
For A. D. A.  
Double Stud  
in position while you are marking the locations.  
Compliance  
27”  
(68.5 cm)  
2. Shim changer for a snug fit.  
A. F. F  
Fig. b  
3. Align holes in changer with marked holes and secure using the  
appropriate fasteners (Fig. c).  
Recess  
Recess  
Mounting  
Holes  
Mounting  
Holes  
NOTE: It is installers responsibility to provide correct fastereners  
for other substrates.  
4. Ensure all seven (7) fasteners are tight.  
Recess  
Mounting  
Holes  
Fig. c  
INSTALLATION - SURFACE-MOUNT  
Recommended Blocking:  
Top  
If the walls do not have studs on center, then additional blocking is  
necessary (Fig. d).  
Contact an architect or building contractor to make sure the  
14 3/4  
blocking is adequate and complies with building codes.  
(374.7 mm)  
For A. D. A.  
Compliance  
48 1/2”  
(123 cm)  
For A. D. A. compliance, measure up 48 1/2” (123 cm) from the  
floor and mark the wall. This locates the position for the top left  
attachment hole.  
48"  
(1219 mm)  
on center  
A. F. F  
Fig. d  
NOTE:  
- Changer MUST be mounted to studs (Fig. e).  
- This unit incorporates a finishing collar that seats behind  
the changer’s outside flange. Center the collar as the unit  
is being tightened against the wall (Fig. f).  
Surface-Mount  
Holes  
Surface-Mount  
Holes  
Collar  
Wall  
Unit  
Fig. e  
Fig. f  
2
 

Eagle Electronics Fish Finder 250 DS User Manual
Eclipse Fujitsu Ten Car Stereo System AVN2227P User Manual
Electro Voice Portable Speaker E V ONE User Manual
Extron electronic Switch VSW 2VGA A User Manual
Field Controls Air Cleaner Eliminator User Manual
Fisher Price Motorized Toy Car 77760 User Manual
GE Clothes Dryer DCCB330EG User Manual
Gemini Turntable XL 100 User Manual
Global Upholstery Co Indoor Furnishings 3672 User Manual
Goodman Mfg Heat Pump GSZ110903AA User Manual