Frigidaire Dishwasher 675000800908 User Manual

6. If levelers need to be removed, make sure that the floor is free of all  
Installation Preparation  
NOTE: Put unit on its back being careful not to pinch the Water  
Drain Hose.  
Dishwasher  
obstructions.  
2
Property Damage  
7. Carefully place dishwasher inside cabinet area such that is  
centered in opening. Use caution when moving dishwasher to  
preventdamagetocabinet, dishwasherandfloor.  
Do not use the furnished drain hose or a rubber garden hose  
for the water supply line. Either of these hoses can burst.  
Flooding may occur and cause property damage.  
Installation  
Instructions  
1. Remove two (2) screws at front of the kickplate using a #2  
Phillips screw driver.  
8. Front of door needs to be even with the front of adjoining cabinets.  
Frontlevelersshouldallow5/16belowundersideofcountertop  
to top of console.  
2. Tilt and pull forward to remove see figure 1a.  
NOTE: It is not necessary to remove the outer door for installation.  
Leveling and Securing  
Dishwasher within  
Cabinets  
Printed in U.S.A.  
675000800908  
5
9. Check that dishwasher is level from side to side by placing a level  
against the top front section of the tub. See Figure 5a.  
08/09  
Figure 3  
*DIMENSIONS DO NOT INCLUDE INSULATION  
INSTALLER: Leave Installation Instructions with owner.  
IMPORTANT: For proper operation and appearance of unit,  
cabinet opening should have dimensions as shown in Figure 2.  
If unit is to be placed in a corner, there must be at least a 2-inch  
side clearance to open door.  
OWNER: Read your dishwasher Use and Care Manual. It contains  
important safety information for operating this appliance. It also has  
many suggestions for getting the best results from your dishwasher.  
IMPORTANT: Drain, water, and electrical lines should be  
roughed-in before going any further.  
BeforeYou Begin  
Figure 5a  
Figure 5b  
Read all instructions before installing dishwasher.  
For your safety, please read and observe all safety  
instructions. This guide will help you anticipate drain, water, and  
electrical connections, and help you select the best location for the  
dishwasher.  
10. Check that the dishwasher is level from front to back by taking  
out the lower rack, place level on the lower rack wheel support at  
the bottom of the tub. See Figure 5b.  
1. Measure height of cabinet opening from underside of countertop  
Figure 1a  
to floor.  
Electric Shock Hazard  
Electrical, water, and drain lines must be confined  
to shaded areas in Figure 2.  
Electric conductors, water, and drain could be  
damaged.  
Failure to follow these instructions could result in  
fire or electric shock.  
2. Move dishwasher to front of installation area.  
11. Adjust levelers up or down until dishwasher is level.  
3. Loosen the rear leveling legs by turning counterclockwise.  
Holes need to be pre-drilled using a #5 drill to secure  
unit.  
Tip Over Hazard  
Do not use dishwasher until completely installed.  
12. Screw mounting brackets firmly to cabinet using screws  
provided in literature packet. See Image Below.  
Dishwasher Anchoring  
Do not push down on open door.  
NOTE: If dishwasher is installed at end of a cabinet, sides and  
back must be fully enclosed.  
5. Choose one of the methods of attachment below to secure unit,  
holes need to be pre-drilled using a #5 drill bit regardless of  
the option chosen:  
Failure to follow this warning can result in serious  
injury.  
a. Top Mount Cabinet Clips (Preferred Method of attachment)  
Connections For Electrical,  
Water, and Drain  
4
b. Side Mount Cabinet Clips (to be used when Side Mount  
Figure 1b  
is not an available option)  
Cut Hazard  
CAUTION: Use extreme care in mounting the dishwasher as  
to not scratch, bump or otherwise damage the console or tub.  
3. Remove two (2) screws at front of the kickplate brace using a  
To prevent serious injury from sharp edges, wear work  
gloves when handling, unpacking or disassembling unit.  
#2 Phillips screw driver. Slide up and pull off.  
Locating the Connections  
4. Locate water inlet valve behind kickplate on bottom left  
underside of unit.See Figure 4. The valve has a 3/8” NPT female  
fitting.  
To install using Top Mount Cabinet Clips:  
1. Review dimensions in Figure 2 to locate dishwasher’s drain,  
Figure 5c  
Figure 5d  
water, and electrical connections.  
Depending on the depth of cabinet, the Top Mount  
Clip have a break off point that can be removed if  
necessary.  
2. All utilities must be routed in shaded area in the Figure 2.  
IMPORTANT: Disconnect power before starting installation.  
Note: Locate the electrical supply and dishwasher’s electrical  
Installation Tips  
5. Wrap 90° elbow (not included) with pipe thread tape (or apply  
joint compound) and thread it into water inlet valve. When  
tightened, elbow should point toward the left. To prevent bending  
ofbracketorbreakingofvalve,avoidovertightening.  
See Figure 4.  
1
13. Open the door remove the tub cap on both sides of the tub.  
Install screw through the dishwasher side hole to the wall of  
cabinet. Reinstall tub cap.  
NOTE: Install Top Mount Clips before unit is installed into the  
cabinet. Insert the installation brackets to the front  
top slots of the dishwasher. (See image below)  
Tools and Materials Needed for  
Installation (Not Included)  
junction box on right underside of unit behind kickplate  
assembly. See Figure 4. Determine where you will connect  
to hot water supply. Review Figure 4 and note the location of  
water inlet valve. Determine where you will connect the drain  
hose.  
Cabinet Preparation:  
Drill, Electric  
As a precaution, it is recommended, but not required that the  
cabinets enclosing all sides of the dishwasher (including the  
underside of the countertop) be sealed with an oil based paint  
or moisture-proof polyurethane to prevent possible steam/  
moisture damage.  
5
Driver, Socket /32”, 1/4,5/16”  
Flaring Tool / Tube Cutter (for copper tubing)  
Flashlight  
Level  
Pipe Joint Compound (for iron pipe plumbing) or  
Pipe Thread Tape (for sealing threads)  
Pliers  
3. Cut access holes for the Electrical, Water and Drain hoses in the  
shaded areas as shown in Figure 2.  
4. The dishwasher operates on a 120 volt, 60 Hz electrical supply.  
Provide a separate circuit with a fuse or circuit breaker rated for  
at least 15 amps (20 amps if connected with disposer) but not  
more than 20 amps.  
Roughing In  
3
Safety Glasses  
5. Pull electrical cable through hole into installation area.  
Saw, Keyhole or 1/2”, 11/2” to 2” Hole Cutters  
Screw Drivers, Slotted and #2 Phillips (magnetic tip  
preferred)  
6. Be sure water inlet valve is protected from freezing. If valve  
freezes and ruptures, flooding may occur.  
7. Determine amount of tubing needed to connect hot water supply  
to the unit’s water inlet valve. Extra hose length is necessary.  
High-pressureandhigh-temperatureStainlessFlexiblehosewith  
Electric Shock Hazard  
Tape, Electrical or Duct  
Tape, Measuring  
Wire Stripper or Utility Knife  
Wrench, Hex-end  
Wrenches, 2 Adjustable (for copper tubing)  
or 2 Pipe wrenches (for iron pipe plumbing)  
To install the Side Mounting Clips.  
Observe all local codes and ordinances for  
electrical and plumbing connections. All electrical  
and plumbing work should be performed by  
qualified persons. Failure to follow this warning  
could result in death or serious injury.  
Depending on space allowed in cabinet the Side Mounting  
Clips can be installed with the holes for the screw up (preferred  
method) or down as shown in the illustrations below.  
1
a minimum inner diameter of /4” may be used. A shut-off valve  
installed outside dishwasher cabinet is best.  
8. Route water supply line into installation area.  
9. Stand dishwasher back upright for further installation.  
NOTE: Install Side Mount Brackets before unit is installed into  
the cabinet. Insert the installation brackets to the side slots  
of the dishwasher. (See image below)  
IMPORTANT: Incoming hot water temperature should be at  
least 120°F (49°C). Water pressure should be between  
20–90psi.  
1. Make sure your location has the correct drain, water, and  
electrical outlets to make the connections. Do not install unit  
under a cooktop range. Damage to tub or other components will  
occur.  
PartsYou Will Need* (Not Included)  
14. Open and close dishwasher door slowly. Ensure that there is  
clearance to the console. Adjust accordingly until door opens  
and closes freely.  
• Brass Elbow, 90° with a 3/8” National Pipe Thread  
• ConduitConnector(ULListed)  
2. Floor should be flat and free of any obstruction.  
• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)  
*
If required:  
• “YBranchTailpieceand  
Connector Kit (See Step 4)  
• Air Gap Kit (See Step 4)  
All the parts can be found at local hardware, electrical and  
plumbing supply stores.  
Electric Shock Hazard  
Figure 4  
Disconnect electrical power at the fuse box or  
circuit breaker box before beginning installation.  
Failure to follow this warning could result in death  
or serious injury.  
WATERLINE  
ELECTRICAL BOX  
(NOT INCLUDED)  
Figure 2  
 

Edelbrock Water Pump 8882 User Manual
Ei Electronics Smoke Alarm Ei 204EN User Manual
Ei Electronics Smoke Alarm Ei3105TYCH User Manual
Esoteric CD Player X 05 User Manual
Exide Battery Charger S47 0079 User Manual
FieldServer Computer Drive FS 8700 24 User Manual
Gaggenau Telescope WS461710 User Manual
GE Refrigerator 18 19 User Manual
GE Ventilation Hood PVB94SN User Manual
Gigabyte Network Card GN WPKG User Manual