Frigidaire Dishwasher FDB2410HIC User Manual

PumpAssembly  
ProductSpecifications  
Electrical  
Trouble Shooting Tips  
Water Supply  
The drain hose must have a loop at a minimum  
height of 32 inches in order to insure proper  
drainage.  
The pump assembly is driven by a synchronous  
motor. The motor drives a pump which supplies  
100 percent filtered water  
Suggested minimum incoming water  
temperature ............................ 120°F (49°C)  
Pressure (PSI) min./max. .................. 20/120  
Connection (NPT) ..................................... 3/8  
Consumption (Normal Cycle) ......................  
.......................................... 5.2 - 5.6 U.S. gal  
Water valve flow rate (U.S. GPM)............ 0.9  
Water recirculation rate (U.S. GPM) ..............  
................................................. approx. 5.28  
Water fill time ................................... 36 sec.  
Rating ...................................120 Volts, 60Hz  
Separate Circuit..15 amp min.- 20 amp max.  
Motor (Amps) ...................................0.6 - 0.9  
Heater Wattage .......................... 475 - 630W  
Total Amps (load rated) .......................... 7.0  
TempAssure .............................. 135°F ±5°F  
(60°C±3°C) [with outer door in place]  
TempBoost ................................ 140°F ±5°F  
Heated Wash/Heated Rinse  
Hi-Limit Thermostat ............... 200°F (93°C)  
Personal Injury Hazard  
Draining is accomplished by using a small  
separate synchronous drain pump mounted to  
the side of the sump. The drain pump is  
connected to the main pump by a small rubber  
hose. The drain check valve is located at the  
discharge end of the drain pump. The drain hose  
is attached by a clamp to the discharge end of  
the drain pump.  
"
Always disconnect the dishwasher from the electrical power source before adjusting or  
replacing components.  
Check the Following  
Remedy  
Symptom  
1. Fuse (blown or tripped).  
2. 120 VAC supply wiring connection  
faulty.  
1. Replace fuse or reset breaker.  
2. Repair or replace wire fasteners at  
dishwasher junction box.  
Dishwasher will not operate when  
turnedon.  
3. Electronic control board defective.  
4. No 12 VAC power to control.  
5. Motor (inoperative).  
6. Door switch (open contacts).  
7. Door latch not making contact with  
door switch.  
8. Touch pad circuit defective.  
9. No indicator lamps illuminate when  
START or OPTIONS are pressed.  
3. Replace control board.  
4. Replace control board.  
5. Replace motor/impeller assembly.  
6. Replace latch assembly.  
7. Replace latch assembly.  
Heater  
Refer to the cycle chart on the reverse side to  
determine when the heater is on during the  
wash cycle. The heater cycles ON and OFF for  
brief periods during the drying cycle.  
Voltage checks of the heater should be made in  
the dry portion of the service test mode.  
8. Replace console assembly.  
9. Replace console assembly.  
1. Motor (bad bearings).  
2. Motor stuck due to prolonged  
non-use.  
1. Replace motor assembly.  
2. Rotate motor impeller.  
Motor hums but will not start or run.  
Standard Dry Air Flow  
The water on the dishes is evaporated into drier  
air and the venting process continues. The  
heatingelementisturnedONandOFFduringthe  
entire drying cycle.  
The heated, moist air leaving the dishwasher  
through the console vent causes drier air to be  
drawn into the unit by way of intake vents located  
at the bottom of the door.  
1. Improper voltage.  
2. Motor windings shorted.  
3. Glass or foreign items in pump.  
1. Check voltage.  
2. Replace motor/impeller assembly.  
3. Clean and clear blockage.  
Motor trips out on internal thermal  
overloadprotector.  
1. Heaterelement(open).  
1. Replace heater element.  
2. Replace control board.  
3. Repair or replace.  
Dishwasher runs but will not heat.  
2. Electronic control board defective.  
3. Wiring or terminal defective.  
4. Hi-Limit thermostat defective.  
DetergentandRinseAidDispenser  
4. Replace thermostat.  
The detergent and rinse aid dispenser is a one To replace dispenser:  
1. Latch mechanism defective.  
2. Electronic control board defective.  
3. Wiring or terminal defective.  
4. Broken spring(s).  
1. Replace dispenser.  
2. Replace control board.  
3. Repair or replace.  
4. Replace dispenser.  
5. Replace dispenser.  
Detergent cover will not latch or  
open.  
piece component consisting of a molded  
detergent cup and a built-in rinse aid dispenser.  
• shut off electricity to dishwasher,  
• remove outer door panel assembly,  
• disconnect wiring to the actuator,  
• remove the six screws,  
• remove the dispenser,  
• replace and reinstall screws,  
The detergent cup has a spring loaded cover  
and the rinse aid dispenser has a removable  
cover.  
5. Defective actuator.  
1. Drain restricted.  
1. Clear restrictions.  
2. Replace control board.  
3. Replacepump.  
4. Check for blockage, clear.  
5. Replace pump assembly.  
6. Repair or replace.  
Dishwasherwillnotpumpout.  
2. Electronic control board defective.  
3. Defective drain pump.  
4. Blocked impeller.  
5. Open windings.  
6. Wiring or terminal defective.  
Liquid rinse aid is added to the dispenser up to • rewire actuator.  
the fill line indicator. The amount of rinse aid  
released can be adjusted by turning the arrow  
indicator from one, being the least amount, to  
four, being the greatest amount.  
1. Water supply turned off.  
2. Defective water inlet fill valve.  
3. Check fill valve screen for  
obstructions.  
1. Turn water supply on.  
2. Replace water inlet fill valve.  
3. Disassemble and clean screen.  
Dishwasher will not fill with water.  
4. Defective float switch.  
5. Electronic control board defective.  
6. Wiring or terminal defective.  
7. Pressure Switch Stuck.  
4. Repair or replace.  
5. Replace control board.  
6. Repair or replace.  
7. Repair or replace.  
1. Drain hose (high) loop too low.  
1. Repair to proper 32-inch minimum  
height.  
2. Install air gap at counter top.  
Dishwasherwatersiphonsout.  
Detergent left in dispenser.  
2. Drain line connected to a floor drain  
not vented.  
1. Detergentallowedtostandtoolongin  
dispenser.  
2. Dispenser wet when detergent was  
added.  
1. Instruct customer/user.  
2. Instruct customer/user.  
3. Detergentcoverheldclosedorblocked  
by large dishes.  
3. Instruct customer/user on proper  
loading of dishes.  
4. Improper incoming water  
temperature to properly dissolve  
detergent.  
4. Incoming water temperature of  
120°F is required to properly  
dissolve dishwashing detergents.  
5. See "Detergent cover will not open."  
020905  
 

Eiki Projector LC SVGA860 User Manual
Electro Voice Portable Speaker PI94 User Manual
Finisar Watch Brocade Fabric Watch User Manual
Focal Car Speaker 27 V1 User Manual
FoodSaver Laptop V875 User Manual
Gateway Personal Computer DX430X User Manual
Gateway Stereo System kas303 User Manual
GE Trash Compactor GCG1700P User Manual
GE Washer WWA8850S User Manual
Glen Dimplex Home Appliances Ltd Oven XOU60F User Manual