Frigidaire Washer Dryer 134126300B User Manual

Laundry Center  
Owner's Guide  
Product Registration.......................................... 2  
Important Safety Instructions.............................2-4  
Washing Procedures .........................................5-7  
Stain Removal...................................................7-8  
Common Washing Problems.............................9  
Drying Procedures............................................. 10  
Features....................................................................11  
Common Drying Problems ................................ 11  
Care and Cleaning............................................ 12  
Avoid Service Checklist .....................................13-15  
Warranty  
.....................................................16  
P/N 134126300B(0407)  
 
Do not operate the dryer if the lint screen is blocked, damaged or  
missing. Firehazard, overheatinganddamagetofabricscanoccur. Ifyourdryerhas  
a drying rack, always replace the lint screen when finished using the drying rack.  
This Owner's Guide provides general  
operatinginstructionsforyourlaundry  
center. It also contains information  
aboutfeaturesforseveralothermodels.  
Your laundry center may not have  
every feature included.  
Keep area around the exhaust opening and surrounding areas free  
from the accumulation of lint, dust and dirt.  
Usethelaundrycenteronlyasinstructed  
in this Owner's Guide.  
Do not obstruct the flow of ventilating air. Do not stack or place  
laundry or throw rugs against the front or back of the laundry center.  
Do not spray any type of aerosol into, on or near laundry center at  
any time.  
Do not use fabric softeners or products to eliminate static unless  
recommended by the manufacturer of the fabric softener or product.  
Avoid fire hazard or  
electricalshock. Donotuseanadaptor  
plug or extension cord or remove  
groundingprongfromelectricalpower  
cord. Failuretofollowthiswarningcan  
cause serious injury, fire or death.  
Failure to comply with these warnings could result in fire, explosion,  
serious bodily injury and/or damage to the rubber or plastic parts of the laundry  
center.  
Protect Children  
14-30R  
Do not allow children to play on or in the laundry center. Close  
supervision of children is necessary when the laundry center is used near children.  
As children grow, teach them the proper, safe use of all appliances.  
DRYER  
FUSED30AMP  
120/240 V OR  
120/208 V  
WALL  
RECEPTACLE  
Destroythecarton, plasticbagandotherpackingmaterialsafterthe  
laundrycenterisunpacked.Childrenmightusethemforplay.Cartonscoveredwith  
rugs, bedspreads or plastic sheets can become airtight chambers.  
DRYER  
SERVICECORD  
CORRECT  
Use this way ONLY  
Keep laundry products out of children's reach. To prevent personal  
injury, observe all warnings on product labels.  
Before the laundry center is removed from service or discarded,  
remove the washer lid and dryer door to prevent accidental entrapment.  
Note: The instructions appearing in  
this Owner's Guide are not meant to  
cover every possible condition and  
situation that may occur. Common  
sense and caution must be practiced  
when installing, operating and  
maintaining any appliance.  
Failuretocomplywiththesewarningscouldresultinseriouspersonal  
injuries.  
Prevent Injury  
To prevent shock hazard and assure stability during operation, the  
laundry center must be installed and electrically grounded by a qualified service  
person in accordance with local codes. Installation instructions are packed in the  
laundry center for the installer's reference. Refer to INSTALLATION INSTRUCTIONS  
fordetailedgroundingprocedures. Ifthelaundrycenterismovedtoanewlocation,  
have it checked and reinstalled by a qualified service person.  
3
 
Important Safety  
Instructions (continued)  
Follow package directions when using laundry products. Incorrect  
usage can produce poisonous gas--resulting in serious injury or death.  
Donotcombinelaundryproductsforusein1loadunlessspecifiedonthelabel.  
Do not mix chlorine bleach with ammonia or acids such as vinegar.  
Topreventseriouspersonalinjuryanddamagetothelaundrycenter:  
All repairs and servicing must be performed by an authorized servicer  
unless specifically recommended in this Owner's Guide. Use only authorized  
factoryparts.  
Do not tamper with controls.  
Do not install or store the laundry center where it will be exposed to the  
weather.  
Do not use or mix  
liquid chlorine bleach with other  
household chemicals such as toilet  
cleaners, rust removers, acid or  
productscontainingammonia.These  
mixtures can produce dangerous  
fumeswhichcancauseseriousinjury  
or death.  
ALWAYS disconnect the laundry center from the electrical supply  
before attempting any service or cleaning. Failure to do so can result in electrical  
shock or injury.  
Do not use any type spray cleanser when cleaning dryer interior.  
Hazardous fumes or electrical shock could occur.  
To prevent injury, do not reach into the washer while parts are  
moving. Beforeloading, unloadingoraddingitems, pushinthecycleselectorknob  
and allow the tub to coast to a complete stop before reaching inside.  
To prevent injury, do not reach into the dryer if the drum is moving.  
Wait until the dryer has stopped completely before reaching into the drum.  
Athermallimiterswitchautomaticallyturnsoffthedryermotorinthe  
unlikely event of an overheated situation (electric dryers only). A service technician  
must replace the thermal limiter switch after correcting the fault.  
The washer is equipped with an electrical overload protector. The  
motorwillstopifitbecomesoverheated. Thewasherwillautomaticallyrestartafter  
acooldownperiodofupto30minutes, ifthewasherhasnotbeenmanuallyturned  
off during this time.  
Failuretocomplywiththesewarningscouldresultinseriouspersonal  
injuries.  
SAVE THESE INSTRUCTIONS  
4
 
Follow the guidelines below for preparing the wash load.  
Washing Procedures  
Read the Washer Operating Instructions, pages 17-18, for operating your  
specific model.  
Always read and follow fabric care and laundry product labels.  
To reduce the risk of fire, electrical shock, or injury to persons, read  
Important Safety Instructions, pages 2-4, before operating this washer.  
1. Sort laundry into loads that can be washed together.  
Sort items by recommended water temperatures, wash time, and agitate/spin  
speeds.  
Separatewhite,light,andcolorfastitemsfromdarkandnoncolorfastitems.  
Separate items which shed lint from items which attract lint. Permanent  
press, synthetic, knit and corduroy items will pick up lint from towels, rugs  
and chenille bedspreads.  
Sortlaundryintoloadsthatcanbe  
washedtogether.  
Separate heavily soiled items from lightly soiled items.  
Separate lacy, sheer and loosely knit items from sturdy items.  
2. Prepare items for washing.  
Empty pockets.  
Brush off lint and dirt. Shake out rugs and beach towels.  
Closezippers,fastenhooks,tiestringsandsashes,andremovenonwashable  
trims and ornaments.  
Remove pins, decorative buttons, belt buckles, and other objects which  
could be damaged. This also helps protect other items in the wash load.  
Mend rips and tears to prevent further damage during washing.  
Placedelicateitemssuchasbras,shoulderpads,hosiery,andbeltsinamesh  
bag to prevent tangling during the wash cycle.  
Turn knit items inside out to prevent pilling.  
Emptypockets.  
3. Pretreat stains and heavy soil.  
See Stain Removal, pages 7-8, for details.  
4. Add a measured amount of detergent to the wash tub  
before adding the laundry load.  
Follow detergent manufacturer's directions. The amount required depends on  
type of detergent, load size and soil level, and water hardness.  
5. Ifdesired,addliquidbleachtoBleachDispenser(somemodels).  
Before adding the wash load, add liquid bleach to bleach dispenser located  
in left front corner under the lid:  
Placedelicateitemsinameshbag.  
3/4 cup (180 ml) for small loads  
1 cup (240 ml) for large loads  
1-1/4 cups (300 ml) for extra-large loads.  
Then add 1 cup (240 ml) water to flush the dispenser.  
Do not use powdered bleach in the bleach dispenser.  
Formodelswithoutableachdispenser,dilutetherecommendedamountof  
liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after  
a few minutes of agitation. Do not pour bleach directly on wash load.  
BleachDispenser(somemodels)  
5
 
6. Add laundry load to washer.  
Washing Procedures  
Dry load level should not be higher than top row of holes in wash tub.  
(continued)  
Do not overload washer.  
Do not put items on top of agitator or wrap them around it. Load items  
evenly.  
Combine large and small items in a load. Load large items first. Large items  
should not be more than half the total wash load.  
When washing a single heavy item, add 1 or 2 towels to balance the load.  
Donotuseliquidchlorinebleachwith  
otherhouseholdchemicals.  
7. If desired, add liquid fabric softener to Fabric Softener  
Dispenser (some models).  
For models with a built-in dispenser (see picture below to the left):  
1. Addliquidsoftenertothedispenser,followingfabricsoftenerlabeldirections.  
2. Add water to bring liquid level to fill line on dispenser cap.  
3. Remove the dispenser from the agitator after each use. Rinse both cap and  
cup with warm water. Replace dispenser in the agitator.  
IMPORTANT: Do not stop and restart washer during a spin when using the  
fabricsoftenerdispenser.  
For models with a removable dispenser (see picture below to the left):  
1. Attachfabricsoftenerdispensertotopofagitatorbypressingdowngently.  
2. Add softener to the dispenser, following fabric softener label directions.  
3. Add water to bring liquid level to top of the peg in the center of the cup.  
4. Remove the dispenser from the agitator after each use. Rinse both lid and  
bowl thoroughly with warm water. Reassemble and place dispenser on  
agitator or store it nearby.  
Donotloaditemsabove  
toprowofholesinwashtub.  
IMPORTANT: Do not stop and restart washer during a spin when using the  
fabricsoftenerdispenser.  
Formodelswithoutafabricsoftenerdispenser,followfabricsoftenerlabel  
directions. Add diluted fabric softener to the final rinse. Do not pour fabric  
softener directly on the wash load.  
Built-InFabricSoftenerDispenser  
(somemodels)  
8. Set cycle selector knob and washer controls according to  
type, size, and soil level of each load, and detergent used.  
See Washer Operating Instructions card for your specific model controls.  
RemovableFabricSoftenerDispenser  
(somemodels)  
6
 
9. Start the washer.  
Close the washer lid and pull out the cycle selector knob. Washer will fill with  
the lid open. The tub will not agitate or spin unless the lid is closed.  
To stop the washer, push in the cycle selector knob.  
To change a cycle, push in the cycle selector knob. Turn it clockwise to the  
desired setting. Pull out the knob to restart the washer.  
10.Remove items when the cycle is completed.  
For your safety, the lid locks when the tub is spinning. It will remain locked for  
about 1 minute after the tub stops spinning.  
Toopenthelidduringaspin, pushinthecycleselectorknobandwaitabout  
1 minute for the lid lock to release. Do not force open the locked lid.  
Place washed items in automatic dryer, line dry, or dry flat as directed by fabric  
care label. Excess wrinkling, color transfer or odors may develop in items left in  
the washer after the cycle has ended.  
Safe Stain Removal Procedures  
Stain Removal  
To reduce the risk of fire or serious injury to persons or property,  
comply with the basic warnings listed below:  
Read and comply with all instructions on stain removal products.  
Keep products in their original labeled containers and out of children's  
reach.  
Thoroughly wash any utensil used.  
Do not combine stain removal products, especially ammonia and chlorine  
bleach. Dangerous fumes may result.  
Never wash items which have been previously cleaned in, washed in,  
soaked in or spotted with gasoline, dry cleaning solvents or other flammable  
or explosive substances because they give off vapors that could ignite or  
explode.  
Do not combine stain removal products.  
Never use highly flammable solvents, such as gasoline, inside the home.  
Vapors can explode on contact with flames or sparks.  
For successful stain removal:  
Remove stains promptly.  
Determine the kind of stain, then follow recommended treatment in the  
stain removal chart on the next page.  
To pretreat stains, use a prewash product, liquid detergent, or a paste made  
from granular detergent and water.  
Use cold water on unknown stains because hot water can set stains.  
Check care label instructions for treatments to avoid on specific fabrics.  
Check for colorfastness by testing stain remover on an inside seam.  
Rinse and wash items after stain removal.  
Followfabriccarelabelinstructions.  
7
 
STAIN  
                                               
                                               
                                                 
                                                 
                                                   
                                                   
                                                     
                                                     
                                                       
                                                        
                                                         
                                                          
                                                             
                                                             
                                                               
                                                               
                                                                 
                                                                  
Stain Removal  
TREATMENT  
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or  
nonflammable dry cleaning fluid.  
Adhesive tape, chewing gum,  
rubber cement  
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.  
Pretreat stain. Wash using cold water and bleach safe for fabric.  
Baby formula, dairy products,  
egg  
Beverages (coffee, tea, soda,  
juice, alcoholic beverages)  
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using  
bleach safe for fabric.  
Blood  
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is  
absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable  
dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.  
Candle wax, crayon  
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.  
Pretreat with prewash stain remover or rub with bar soap.  
Chocolate  
Collar or cuff soil, cosmetics  
Dye transfer on white fabric  
Grass  
Use packaged color remover. Wash using bleach safe for fabric.  
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.  
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply  
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash  
using hottest water safe for fabric.  
Grease, oil, tar (butter, fats,  
salad dressing, cooking oils,  
car grease, motor oils)  
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured  
alcohol or nonflammable dry cleaning fluid.  
Ink  
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly  
mildewed fabrics may be permanently damaged.  
Mildew, scorch  
Brush off dry mud. Pretreat or soak with product containing enzymes.  
Pretreat with prewash stain remover. Wash using bleach safe for fabric.  
Mud  
Mustard, tomato  
Nail polish  
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.  
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.  
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL  
BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.  
Paint, varnish  
Perspiration  
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for  
fabric.  
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and  
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.  
Rust, brown or yellow  
discoloration  
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat  
with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.  
Wash using bleach safe for fabric.  
Shoe polish  
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.  
Urine, vomit, mucus, feces  
8
 
Common Washing Problems  
Manywashingproblemsinvolvepoorsoilandstainremoval,residuesoflintandscum,andfabricdamage.Forsatisfactorywashing  
results, follow these suggestions provided by The Soap and Detergent Association.  
SOLUTIONS  
PROBLEM  
PREVENTIVE MEASURES  
POSSIBLE CAUSES  
Blue stains  
•Detergent or liquid fabric softener •If caused by detergent, mix 1 cup (240 ml)  
•Add detergent before wash load. Then  
start washer.  
did not dissolve or disperse.  
white vinegar with 1 quart (.95 L) water in a  
plastic container. Soak item 1 hour. Rinse.  
•If caused by fabric softener, rub stains with  
bar soap. Wash.  
•Dilute fabric softener with water.  
Discoloration,  
graying  
•Not enough detergent.  
•Wash water temperature too low.  
•Incorrect sorting.  
•Rewash with correct amount of detergent  
and hottest water safe for fabric. Add  
bleach safe for fabric.  
•Sort items by soil level and color.  
•Use correct amount of detergent, hottest  
water and bleach safe for fabric.  
Greasy, oily stains  
•Not enough detergent.  
•Undiluted liquid fabric softener  
poured directly on fabric.  
•Treat with prewash stain remover or liquid  
detergent.  
•Increase detergent and water temperature. Do not pour liquid fabric softener directly  
•Use correct amount of detergent and hottest  
water safe for fabric.  
on fabric. See package directions or Washing  
Procedures for proper diluting.  
Rewash.  
•Rub fabric softener stains with bar soap.  
•Never pour chlorine bleach directly on  
fabric.  
•Check condition of items before washing.  
See Washing Procedures for preparing  
and loading the wash load.  
Holes, tears, or  
snags  
•Incorrect use of chlorine bleach.  
•May be irreversible if rips, tears and seams  
•Unfastened zippers, hooks, buckles. cannot be mended.  
•Rips, tears and broken threads.  
•Overloading the washer.  
•Degradation of fabric.  
Lint  
•Incorrect sorting.  
•Reduce load size. Rewash using correct  
water temperature, water level, and  
amount of detergent.  
•Add nonprecipitating water conditioner to  
wash water.  
•Add liquid fabric softener to final rinse.  
•Dry load in dryer.  
•See Washing Procedures for sorting and  
preparing the wash load.  
•Do not overload washer.  
•Use correct amount of detergent, water  
temperature and water level.  
•Tissues left in pocket.  
•Overloading the washer.  
•Not enough detergent.  
•Undissolved detergent has left  
residue.  
•Static cling is attracting lint.  
•Load washed too long.  
•Remove lint with lint brush or roller.  
•Use fabric softener in the washer to  
lubricate fibers.  
•When ironing, use spray starch or fabric  
finish on collars and cuffs.  
Pilling  
•Pilling is normal with synthetic and  
permanent press fabrics. This is due  
to abrasion from normal wear.  
•Use a lint brush or shaver to remove pills.  
(Fibers break off,  
ball up and cling to  
fabric)  
•Turn items inside out to reduce abrasion.  
•Increase water temperature using hottest  
water safe for fabric.  
•Do not overload washer.  
•Use liquid detergent or use  
nonprecipitating water conditioner with  
nonphosphate granular detergent.  
•Undissolved detergent.  
•Some nonphosphate granular  
detergents can combine with hard load.  
water minerals to form a residue. •Mix 1 cup (240 ml) white vinegar to 1 gallon  
(3.8 L) warm water in plastic container.  
•Reduce load size.  
•Add dissolved detergent to tub . Rewash  
Residue or powder  
on dark items;  
Stiff, harsh fabrics.  
Soak item. Rinse and rewash.  
•Do not overload washer.  
•Remove items from washer as soon as  
cycle is completed.  
•Overloading the washer.  
•Reduce load size.  
•Rinse in cold water with liquid fabric  
softener.  
Wrinkling  
•Use liquid fabric softener.  
•Wash synthetics frequently using water at  
least 100°F (37°C ) and correct water level.  
•Agitation time too short.  
•Wash water temperature too low.  
•Not enough detergent.  
•Soak in detergent booster or product  
containing enzymes.  
•Wash in hot water (120°F/49°C) using full  
permanent press cycle. Increase detergent.  
Add bleach safe for fabric.  
Yellow buildup of  
body soil on  
synthetic fabrics  
•Or, treat with color remover.  
•Use nonprecipitating water softener.  
•Before washing, run hot water for a few  
minutes to clear lines.  
•Drain water heater occasionally.  
•For an ongoing problem, install an iron  
filter in your water supply system.  
•Iron or manganese in water supply, •To restore discolored load of whites, use rust  
Yellow or brown  
rust stains  
water pipes, or water heater.  
remover safe for fabric.  
Do not use chlorine bleach to remove  
rust stains. It may intensify  
discoloration.  
9
 
Follow the guidelines below for preparing the load for drying.  
Drying Procedures  
ReadtheDryerOperatingInstructions,pages19-20,foroperatingyourspecific  
model.  
• Always read and follow fabric care labels and laundry product labels.  
To reduce the risk of fire, electrical shock, or injury to persons, read  
Important Safety Instructions, pages 2-4, before operating this dryer.  
1. Prepare items for drying.  
Dry items of similar fabric, weight and construction in the same load.  
Separate dark items from light-colored items. Separate items that shed lint  
from those that attract lint. If an item sheds lint, turn it inside out.  
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum  
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand  
sashes to prevent snagging and tangling.  
If possible, turn pockets inside out for even drying.  
Followfabriccarelabelinstructions.  
Check for stains which may not have been removed in washing. Dryer heat  
may permanently set some stains. Repeat stain removal process before  
drying.  
Place small items in a mesh bag to prevent tangling and for easy removal.  
2. Check that lint screen is clean and in place.  
3. Load the dryer.  
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble  
freely for even drying and less wrinkling. Do not overload dryer.  
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall  
and medium sized items.  
For delicate or very small loads, add 2 lint-free towels for better drying, less  
wrinkling, and to prevent grease stains caused by fabric softener sheets.  
Placesmallitemsinameshbag.  
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,  
and a build-up of static electricity, which can produce more lint.  
If desired, add a dryer fabric softener sheet.  
4. Close the dryer door and set dryer controls (some models).  
See Dryer Operating Instructions card for your specific model controls.  
5. Turn cycle selector clockwise to the desired setting.  
6. Start the dryer.  
Turn Start control clockwise to ON. Hold for 1-2 seconds and release.  
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer  
will always stop when the door is opened.  
Allow the drum to come to a complete stop before reaching inside.  
Filldryerdrum1/3to1/2full.  
7. When the cycle ends, remove items immediately and hang  
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.  
10  
 
Cycle Signal Control (some models)  
Features  
WhentheCycleSignalControlisON, asignalwillsoundattheendofeachcycleand  
during the Press Saver setting (some models). The volume is adjustable on some  
models.  
Drum Light (some models)  
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum  
during loading and unloading. Closing the door turns off the light.  
Drying Rack (some models)  
Use the drying rack to dry items which should not be tumble dried.  
1. Open the dryer door and remove the lint screen.  
2. Insertdryingrackintothedryerdrum. Placethefrontbarunderthelipofthelint  
screen opening. The side bars should sit in the notches of the frame.  
3. Place items to be dried on top of rack. Weight should not exceed 10 lbs. Leave  
space between items, but do not let items hang over the sides or through the  
grids. Do not tumble other items when using the drying rack.  
4. Selectatimeddrysettingbestsuitedforitemsbeingdried. UseonlytheAirFluff  
(noheat)temperaturesettingforitemscontainingplastic,foamrubber,rubber-  
like materials, feathers or down.  
5. When items are dry, remove the rack and replace the lint screen. If lint screen  
isnotinplace,tumblingitemscouldentertheexhaustsystemandcausedamage  
to the dryer.  
Usethedryingracktodryitemswhich  
shouldnotbetumbled.  
Common Drying  
Problems  
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.  
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.  
PREVENTIVE MEASURES  
PROBLEM POSSIBLE CAUSES SOLUTIONS  
Greasy, oily  
stains  
•Rub fabric softener stains with bar soap. •Add a few bath towels to small loads for proper  
•Fabric softener sheet.  
Rinse and rewash.  
tumbling.  
•Some "silk-like" fabrics should be air dried.  
•Use proper drying temperature.  
•Place fabric softener sheet on top of load before  
starting the dryer.  
Lint  
•Reduce load size and rewash using liquid •Do not overload dryer.  
•Overloading.  
fabric softener in the final rinse.  
•Or, add a fabric softener sheet and  
tumble without heat.  
•Use fabric softener in washer or dryer to reduce  
static electricity.  
•Remove items when they are slightly damp to  
avoid overdrying.  
•Overdrying causes static  
electricity.  
•Lint screen not clean when  
cycle began.  
•Use lint brush or roller to remove lint.  
•Check that lint screen is clean and in place.  
•Lint is attached to "pills."  
Pilling  
•Use a lint brush or shaver to remove pills. •Use fabric softener to lubricate fibers.  
•When ironing, use spray starch or fabric finish on  
collars and cuffs.  
•Pilling is normal with synthetic  
and permanent press fabrics.  
This is due to abrasion from  
normal wear.  
(Fibers break off,  
ball up and cling  
to fabric.)  
•Turn items inside out to reduce abrasion.  
Shrinking  
Wrinkling  
•Irreversible condition.  
•Follow fabric care label directions.  
•If shrinking is a concern, check load often.  
•Remove items while slightly damp.  
•Block knits into shape.  
•Overdrying.  
•Lay flat to complete drying.  
•Reduce load size and tumble at medium •Do not overload dryer.  
•Overloading.  
or low heat for 5-10 minutes.  
•Remove items immediately.Hang or fold.  
•Remove items as soon as cycle ends.  
•Leaving items in dryer after  
cycle ends.  
11  
 
To reduce risk of fire or serious injury to persons or property, comply  
with the basic warnings listed in Important Safety Instructions, pages 2-4, and  
those listed below.  
Care and Cleaning  
Beforecleaningthewasherordryerinterior,unplugtheelectricalpowercord  
to avoid electrical shock hazards.  
Do not use any type spray cleanser when cleaning dryer interior. Hazardous  
fumes or electrical shock could occur.  
Inside the Washer  
Removeitemsfromthewasherassoonasthecycleends.Excesswrinkling,color  
transfer, and odors may develop in items left in the washer.  
Dry the washer top, the area around the lid opening, and the underside of the  
lid. These areas should always be dry before the lid is closed.  
Beforecleaningthewasherinterior,unplugtheelectricalpowercordtoavoid  
electrical shock hazards.  
Cleanlintscreenaftereveryload.  
When extremely soiled items have been washed, a dirty residue may remain on  
the tub. Remove this by wiping the tub with a nonabrasive household cleanser.  
Rinsethoroughlywithwater.  
The agitator or tub may become stained from fabric dye. Clean these parts with  
a nonabrasive household cleanser. This prevents dye transfer to future loads.  
Inside the Dryer  
Clean the dryer lint screen after every load. Lint build-up in the screen restricts  
air flow, which causes longer drying times. The screen is located at the bottom  
ofthedooropening.Removebypullingstraightup.Removethelintandreplace  
the screen.  
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added  
fabric softener sheets. To remove this build-up, wash the lint screen in warm,  
soapy water. Dry thoroughly and replace. Do not operate the dryer without the  
lint screen in place.  
Washlintscreenoccasionally.  
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith  
a damp cloth and a mild liquid household cleanser. Remove cleanser residue  
before drying the next load.  
Usecarewithlaundry  
products.Theycandamagefinishon  
thelaundrycenter.  
Every 18 months an authorized servicer should clean the dryer cabinet interior  
and exhaust duct. These areas can collect lint and dust over time. An excessive  
amountoflintbuild-upcouldresultininefficientdryingandpossiblefirehazard.  
Outside  
When laundering is completed, wipe cabinet with a damp cloth. Turn water  
faucets off to prevent pressure build-up in the hoses.  
Clean the cabinet with mild soap and water. Never use harsh, gritty or  
abrasivecleansers.Ifthecabinetbecomesstained,cleanwithdilutedchlorine  
bleach [1/2 cup (120 ml) in 1 quart (.95 L) water]. Rinse several times with clear  
water.  
Remove glue residue from tape or labels with a mixture of warm water and mild  
detergent. Or, touch residue with the sticky side of the tape or label.  
Beforemovingthelaundrycenter,placeastripofcardboardorthinfiberboard  
under the front leveling legs to prevent floor damage.  
12  
 
WinterizingInstructions  
Ifthelaundrycenterisstoredinanareawherefreezingcanoccurormovedinfreezing  
temperatures,followthesewinterizinginstructionstopreventdamagetothelaundry  
center:  
Follow Winterizing  
Instructions for cold  
weather care.  
1. Turn off water supply faucets.  
2. Disconnect hoses from water supply and drain water from hoses.  
3. Plug electrical cord into a properly grounded electrical outlet.  
4. Add 1 gallon nontoxic recreational vehicle (RV) antifreeze to empty wash tub.  
Close lid.  
5. Set cycle selector knob at a spin setting. Pull out knob and let washer spin for 1  
minute to drain out all water. Not all of the RV antifreeze will be expelled.  
6. Push in knob, unplug electrical power cord, dry tub interior, and close lid.  
7. Store washer in an upright position.  
8. To remove antifreeze from washer after storage, run empty washer through a  
complete cycle using detergent. Do not add wash load.  
Avoid Service Checklist  
Before calling for service, review this list. It may save both time and expense. The list includes common concerns that are not the  
result of defective workmanship or materials in this laundry center.  
SOLUTION  
OCCURRENCE  
POSSIBLE CAUSE  
WASHER - NOISE  
"Clunking" or gear sounds.  
This is normal.  
A certain amount of "clunking" or gear  
sounds are normal in a heavy-duty  
washer.  
Rattling and clanking noise.  
Stop washer and check tub. If noise continues after  
washer is restarted, objects may be in pump. Call your  
authorized servicer.  
Foreign objects such as coins or safety  
pins may be in tub or pump.  
To prevent unnecessary noise and damage to tub,  
fasten fasteners and turn items inside out.  
Belt buckles and metal fasteners are  
hitting wash tub.  
Squealing sound or hot  
rubber odor.  
Do not overload washer. Stop washer and reduce load.  
Washer is overloaded.  
Thumping sound.  
This is usually normal. If sound continues, washer is  
probably out of balance. Stop washer and redistribute  
wash load.  
Heavy wash loads may produce a  
thumping sound.  
Vibrating noise.  
Move laundry center so it rests firmly on solid floor.  
Additional floor bracing may be needed. Adjust leveling  
legs. See INSTALLATION INSTRUCTIONS for details.  
Laundry center is not resting on a solid,  
firm floor.  
See INSTALLATION INSTRUCTIONS for removing  
shipping bolt and block.  
Shipping bolt and block have not been  
removed during installation.  
Stop washer and rearrange wash load.  
Make sure plug fits tightly in wall outlet.  
Wash load unevenly distributed in tub.  
WASHER - OPERATING  
Washer does not start.  
Electrical power cord may not be plugged  
in or connection may be loose.  
Reset circuit breaker or replace fuse. Do not increase  
fuse capacity. If problem is a circuit overload, have it  
corrected by a qualified electrician. If problem is a  
power outage, call local electric company.  
Housefuseblown, circuitbreakertripped,  
or a power outage has occurred.  
Turn on water supply faucets.  
Water supply faucets are not turned on.  
13  
 
OCCURRENCE  
POSSIBLE CAUSE  
SOLUTION  
WASHER - OPERATING  
(continued)  
Washer does not start  
(continued).  
Cycle selector is not in correct position.  
Motor is overheated.  
Move indicator clockwise slightly. Pull out knob.  
Washer motor will stop if it becomes overheated. It will  
automatically restart after a cool down period of up to 30  
minutes (if washer has not been manually turned off).  
Washer won't spin.  
Residue left in tub.  
Lid is not completely closed.  
Heavily soiled items.  
Close lid completely.  
Wipe tub with a nonabrasive household cleanser, then  
rinse. Shake or brush excess dirt and sand from items  
before washing.  
WASHER - WATER  
Washloadtoowetafterspin. Washer is overloaded.  
Do not overload washer. See Washing Procedures.  
Rearrange load to allow proper spinning.  
Straighten drain hose.  
Load is out of balance.  
Drain hose is kinked.  
Waterdoesnotenter washer Water supply is not adequate in area.  
or it enters slowly.  
Checkanotherfaucetinthehouse.Waituntilwatersupply  
and pressure increase.  
Water supply faucets are not completely open. Fully open hot and cold faucets.  
Water is being used elsewhere in the house.  
Water pressure must be at least 30 psi (260 kPa). Avoid  
running water elsewhere while washer is filling.  
Water inlet hoses are kinked.  
Straighten hoses.  
Water level does not cover Improper water level selection (for  
Select higher water level/load size.  
load.  
models with water level/load size control).  
Washer is overloaded.  
Do not overload washer. When control is set at highest fill  
level, dry load level should not be higher than top row of  
circular holes in wash tub.  
Warmorhotwaterisnothot Hot water heater is set too low or is a  
Measure hot water temperature at nearby faucet with  
candy or meat thermometer. Water temperature should  
be at least 130°F (70°C). Adjust water heater as necessary.  
enough.  
distance from laundry center.  
Avoid using hot water elsewhere before or during washer  
use. There may not be enough hot water available for  
propercleaning.Ifproblempersists,yourhotwatersystem  
may be unable to support more than 1 use at a time.  
Hot water is being used elsewhere in  
the house.  
Drain hose is kinked or clogged.  
Clean and straighten the drain hose.  
Water in washer does not Fill hose connection at faucet or washer.  
drain or drains slowly.  
Checkandtightenhoseconnections.Installrubbersealing  
washers provided.  
Water leaks.  
House drain pipes are clogged.  
Oversudsing.  
Unclog drain pipes. Contact plumber if necessary.  
Use less detergent.  
Incorrect wash and rinse Hot and cold water hoses are connected  
temperatures. to wrong supply faucets.  
Connecthotwaterhosetohotwaterfaucetandcoldwater  
hose to cold water faucet.  
Waterisenteringwasherbut Drain hose standpipe is incorrect height.  
tub does not fill.  
Standpipe must be a minimum of 33" (83.82 cm) high to  
prevent siphoning. See INSTALLATION INSTRUCTIONS.  
14  
 
OCCURRENCE  
DRYER  
POSSIBLE CAUSE  
SOLUTION  
Dryer does not start.  
Make sure the plug fits tightly in wall outlet.  
Electrical power cord is not securely  
plugged in or plug may be loose.  
Reset circuit breaker or replace fuse.  
House fuse blown or circuit breaker  
tripped.  
Make sure electrical line is not overloaded and the dryer  
is on a separate circuit.  
Call authorized service person for replacement.  
Replace fuse.  
Thermal limiter tripped.  
Dryer runs but won't  
heat.  
There are 2 house fuses in the dryer  
circuit. If 1 of the 2 fuses is blown, the  
drum may turn but the heater will not  
operate.  
Check to make sure supply valve is open. See  
INSTALLATION INSTRUCTIONS for procedure.  
Gas supply valve is not open (gas models).  
See INSTALLATION INSTRUCTIONS.  
Dryer does not have enough air supply to  
support the burner flame (gas models).  
Refill or replace tank.  
LP gas supply tank is empty or there has  
been a utility interruption of natural gas  
(gas models).  
Dryer should heat when utility service is restored.  
Drying cycle takes too  
long, outsideofthedryer  
feels too hot or smells  
hot.  
Make sure all lint has been removed from the dryer lint  
screen before starting each cycle.  
Lint screen is clogged with lint.  
Exhaust duct must be at least 4 inches in diameter and  
made of rigid or flexible metal.  
Exhaust duct requirements have not been  
met.  
When in place, the duct must have no more than two  
90° bends and must not exceed length listed in  
INSTALLATION INSTRUCTIONS.  
Drying time will be 20% longer than drying on a 240 volt  
circuit.  
Electric dryer is connected to a 208 volt  
circuit.  
See Drying Procedures, page 10.  
Drying procedures have not been  
followed.  
Clean out any obstruction.  
Outside exhaust hood or exhaust duct  
may be clogged or restricted.  
Use a dehumidifier near the dryer.  
High humidity.  
Excessive wrinkling.  
Do not overload. See Drying Procedures, page 10.  
Remove items as soon as cycle ends.  
See Drying Procedures, page 10.  
Dryer is overloaded.  
Items left in dryer too long.  
Insufficient sorting of items.  
Drying temperature too high.  
Follow fabric care label instructions.  
15  
 
WARRANTY (CANADA)  
LAUNDRY CENTER  
WARRANTOR:  
Forserviceunderthiswarranty,contactyourlocaldealer/  
retailer, authorized ELECTROLUX HOME PRODUCTS PARTS  
AND SERVICE depot, or:  
ELECTROLUX HOME PRODUCTS CANADA  
6150 McLaughlin Road, Unit#1  
Mississauga,Ontario  
ELECTROLUX HOME PRODUCTS CANADA  
6150 McLaughlin Road, Unit#1  
Mississauga,Ontario  
L5R 4C2  
L5R 4C2  
Tel.:  
Fax:  
(905)568-3433  
(905)568-3542  
WARRANTOR WILL THROUGH ITS AUTHORIZED  
SERVICEDEPOT:  
WARRANTYPERIOD:  
Forthefirst yearafterpurchasebytheoriginalconsumer/  
owner:  
Pay all costs to repair or replace any defective parts.  
For twenty five years after purchase by the original  
consumer/owner:  
Pay allcosts ofadefectivepolypropylenewasherbasket.  
Washer transmission for the second through fifth year  
after purchase by the original consumer/owner:  
Pay all costs (excluding labour to install) to replace any  
defective transmission parts.  
WARRANTYAPPLIESTO:  
a) Products purchased and installed in Canada for personal single family household use.  
b) Defects resulting or arising out of the manufacturing process.  
c) Products bearing legible manufacturer's model and serial numbers.  
d) Replacement parts only for the remainder of the original warranty.  
WARRANTY DOES NOT APPLY TO:  
a) Transportationdamage.  
b) Supply and replacement of porcelain, fuses, glass and light bulbs.  
c) Partsandservicesuppliedorobtainedfromotherthan ELECTROLUX HOMEPRODUCTSPARTSAND SERVICEor ELECTROLUX  
HOME PRODUCTS PARTS AND SERVICE authorized depots.  
d) Damage or failure as the result of abuse, improper or commercial use.  
CONSUMER/OWNERRESPONSIBILITY:  
a) Toprovideproofoftheoriginaldateofpurchasebymeansofabillofsaleorpaymentrecordverifyingpurchasedate.  
b) To pay all costs to make the appliance readily accessible for service.  
c) To ensure proper power supply and connection of the appliance to same.  
d) Proper installation, control setting and care of finish.  
Thiswarrantyisinadditiontoanystatutorywarrantiescontainedinanyapplicablelegislation. Thetermsandconditions  
of this warranty are not intended to exclude or limit your rights under those statutes. The warrantor however reserves  
therighttochargetransportationandtravellingcostsfordistancesinexcessof48kilometres(30miles)fromthenearest  
ELECTROLUX HOME PRODUCTS PARTS AND SERVICE authorized service depot.  
This warranty plus the statutory warranties mentioned are the only warranties given to the consumer/owner for this  
product.  
16  
 

Electro Voice Portable Speaker EVS 14B User Manual
Extron electronic Power Supply 306 User Manual
Extron electronic Power Supply TSC 100 User Manual
Fisher Paykel Dishwasher DW820 User Manual
Fisher Price Baby Toy V3400 User Manual
FujiFilm Film Camera RVP100 User Manual
GBC Paper Shredder RDS 1713 User Manual
GE Monogram Refrigerator ZIS420NX User Manual
GE Oven JRS06 User Manual
Global Machinery Company Lawn Mower RL 500 User Manual