Fujitsu MP3 Docking Station ST4000 Series User Manual

Fujitsu Stylistic®  
ST4000 Series  
TABLET DOCK  
USERS GUIDE  
 
Tablet Dock User’s Guide  
Fujitsu Stylistic ST4000 Series Tablet Dock  
This guide contains information on using your  
Tablet Dock.You should read this section  
before using the dock, even if you are familiar  
with other computer docking devices.  
Do not expose the Tablet Dock to rain,  
moisture, excessive dirt or temperatures  
outside the Environmental Specifications  
as it may cause fire and shock hazards.  
Your Tablet Dock may be configured in one of  
two ways:  
High voltage is present inside the Tablet  
Dock. Do not remove the cover under any  
circumstances. There is a serious shock  
hazard.  
Configuration  
Tablet Dock with CD-ROM Drive  
Switch the unit OFF, unplug the power  
cord and contact a qualified service tech-  
nician or Fujitsu Services and Support if:  
Tablet Dock with Combo DVD/  
CD-RW Drive  
Liquid has been spilled on the Tablet  
Dock.  
Your Fujitsu Stylistic ST4000 Series Tablet  
Dock has the following interfaces:  
The Tablet Dock has been dropped.  
Small objects went inside your  
Tablet Dock which may cause a short  
circuit and/or create a hazard of  
shock.  
Port/Jack  
Purpose  
Allows you to connect a Local  
Area Network (LAN) device or  
broadband device such as a  
cable modem.  
LAN (RJ45)  
Jack  
Fuses continue to blow out.  
A distinct change in the operation and  
performance of the Tablet Dock  
occurs.  
Allows you to connect an  
external monitor.  
VGA Port  
The power cord or plug is damaged  
or frayed.  
Allows you to connect  
headphones or external  
speakers.  
Line Out  
Jack  
The unit should be operated only from the  
type of power indicated on the marked  
label.  
Allows you to connect power to  
the system.  
DC In  
The socket outlet must be installed near  
the equipment to be accessible using the  
system’s AC power cord. Never connect  
the Tablet Dock to AC power by using an  
extension cord.  
Allow you to connect up to three  
Universal Serial Bus (USB)  
Revision 1.1 devices or hubs.  
USB Ports  
(Quantity 3)  
For additional environmental specifica-  
tions, see “Tablet Dock Specifications” on  
page 10.  
Allows you to connect a  
peripheral such as a digital video  
camera.  
IEEE 1394  
Jack  
Always use your Tablet Dock on a solid,  
flat, level, clean, and dry surface. Nearby  
there should be electric power, as well  
as a telephone jack for a modem or a LAN  
port.  
Save packing material in order to safely  
ship or store theTablet Dock in the future.  
3
 
Fujitsu Stylistic ST4000 Series Tablet Dock  
IDENTIFYING THE COMPONENTS  
Before using your Tablet Dock, you should familiarize yourself with its various features.  
Positioning Guide  
Side Latch  
(both sides)  
Back Latch  
Interface Connector  
Lock Release Button  
Lock Handle  
Back Latch  
Positioning Guide  
Platform  
Kensington® Lock Slot  
Front of base  
(Do not use as  
a carrying handle).  
CD-ROM or Combo  
DVD/ CD-RW Drive  
Figure 1. Front View  
Easel Release  
Buttons  
IEEE 1394 Jack  
LAN (RJ-45) Jack  
USB Ports (Qty. 3)  
DC In Jack  
External Monitor (VGA) Port  
Line Out Jack  
Figure 2. Back View  
4
 
Tablet Dock User’s Guide  
DOCKINGYOUR SYSTEM  
Microsoft® Windows® uses “plug- and-play”  
technology to automatically load the files  
necessary to operate your Tablet Dock and any  
attached devices.  
The front portion of the base should not be  
used as a handle.It is designed to support  
the system when it is installed in the Tablet  
Dock, but not as a handle.  
Microsoft® Windows® uses “plug-and-play”  
technology to automatically load the files  
necessary to operate your Tablet Dock and  
any attached devices.  
UNDOCKINGYOUR SYSTEM  
Use these instructions when you want to  
remove your system from the Tablet Dock.  
1. Plug the system’s AC adapter into a wall  
outlet, then into the Tablet Dock’s DC Input  
jack.  
The system can be removed from the Tablet  
Dock whether the system is operating or not.  
2. Set the ST4000 series system on the Tablet  
Dock, with the system oriented in the same  
direction as the dock. (See Figure 3 for  
location). The connector in the back of the  
system should be aligned with the interface  
connector on the Tablet Dock.  
1. Press the lock release button on the top of  
the right slide (above the lock handle).  
While holding it down, pull the lock handle  
upwards to unlatch the back latches from  
the system.  
2. Pull the system upwards, away from the  
platform. The system is now undocked.  
Figure 3. Docking the system  
3. Carefully push the system towards the  
docking port until you hear a click. The click  
indicates that the side latches are in place.  
Note that the system is not yet locked into  
place until the following step is performed.  
4. Firmly pull the lock handle down as far as it  
will go. This engages the back latches and  
side latches, and locks the system in place.  
5. Your Tablet Dock is now ready for use.You  
may now attach devices to it.  
5
 
Fujitsu Stylistic ST4000 Series Tablet Dock  
CHANGING SYSTEM  
ORIENTATION  
Microsoft® Windows® uses “plug-and-play”  
technology to automatically load the files  
necessary to operate your Tablet Dock and any  
attached devices.  
Figure 6. Changing Display from  
Portrait to Landscape Mode  
Figure 4. Portrait Orientation  
Figure 7. Changing Display from  
Landscape to Portrait Mode  
When you change the orientation of the  
system, the display does not change  
orientation. To change the orientation of the  
display, use the Orientation application  
button. (See your system User’s Guide for  
more information).  
Figure 5. Landscape Orientation  
To change the position of the display, simply  
grasp the edge of the system and turn it in the  
direction shown in Figures 6 and 7.  
If the display is in portrait position, turn the  
display to the right, as shown in Figure 6.  
If the display is in landscape position, turn  
the display to the left, as shown in Figure 7.  
6
 
Tablet Dock User’s Guide  
CONNECTING DEVICES  
To Attach External Audio Equipment  
Once your system is installed in the Tablet  
Dock, you are ready to attach external devices  
to the dock.  
The Tablet Dock provides a Line Out jack for  
head-phones or external speakers.  
To Attach an External VGA Monitor  
Connecting external speakers (including  
headphones) or microphone disables the  
system’s internal speaker or internal  
microphone.  
This option allows you to use an external  
monitor with your system. The only  
requirement is that the external device  
(monitor, projector) is a VGA device. Consult  
the instructions that come with the device.  
1. To attach an external audio device, insert  
the plug into the Line Out jack on the back  
of the Tablet Dock (Figure 2).  
1. Securely insert the external monitor plug  
into the display port on the back of the  
Tablet Dock (Figure 2). Always check the  
icon by the port before inserting.  
To Attach a LAN Device  
Tightenscrews if available.  
The LAN (RJ-45) jack allows you to connect  
the system’s internal Fast Ethernet to a LAN,  
or broadband devices such as a cable modem,  
DSL, or satellite internet.  
2. You may switch between the internal  
monitor and external monitor using the  
Display Configuration utility located in the  
system tray at the bottom right of the  
screen, or through the Control Panel  
settings.  
1. To attach a LAN device, insert the plug into  
the LAN (RJ-45) jack on the back of the  
Tablet Dock.  
To Attach a USB device  
Refer to the device manufacturer’s installation  
and usage instructions for configuration  
instructions.  
Use of the USB ports allows attaching USB  
devices to a docked system.  
1. Securely insert the connector into one of  
the three USB ports on the left side of the  
Tablet Dock (Figure 2). It may be necessary  
to wait a short time while the appropriate  
drivers are located and installed by the  
system.  
USING THE INTERNAL MEDIA  
DRIVE  
The Tablet Dock is outfitted with either a CD-ROM  
drive or a Combo DVD/CD-RW drive,  
depending upon the configuration of your dock.  
A CD-ROM drive allows you to access  
software, data, or audio CDs. A DVD/CD-RW  
combo drive allows you to access movies,  
audio, software, data, or audio DVD/CDs, and  
to write data onto recordable CDs.  
To Attach an IEEE 1394 device  
The IEEE 1394 jack allows attaching peripherals  
such as digital cameras to a docked system.  
1. Securely insert the connector into the IEEE  
1394 jack on the left side of the Tablet Dock  
(Figure 2).  
Refer to the device manufacturer’s installation  
and usage instructions for configuration  
instructions.  
7
 
Fujitsu Stylistic ST4000 Series Tablet Dock  
CD-ROM drive  
All of the software you need to run the CD-  
ROM drive is already installed on the  
ST4000 series system. The drive will work  
as soon as the system is docked and  
powered up.  
Prolonged use of the media drive, such  
as watching DVD movie, will  
substantially reduce your battery life if no  
other power source is attached. Be sure  
to attach an AC Adapter when using the  
Tablet Dock for prolonged tasks.  
a
Combo DVD/CD-RW drive  
Packaged with the Tablet Dock is a CD that  
contains the applications required to run the  
DVD and CD/RW features. The combo drive  
will only act as a CD-ROM drive until you  
install the additional software. To install the  
additional software, refer to the instructions  
on the CD.  
All Fujitsu DVD players are set to play  
DVD titles with region code number 3  
which is specified for the Asia Pacific  
market. The region number is a regional  
restriction code defined by the DVD  
Forum consortium.Different region codes  
are recorded on video DVD titles for  
publication in different areas of the world.  
If the regional code of the DVD player  
does not match the regional codes on the  
titles, then playback is impossible.  
The instructions for installing and removing disks  
is the same for both drives. For information about  
the software’s features and capabilities, refer to  
the help files associated with the related  
applications.  
You can change the region code on the  
DVD player using the Properties menu of  
the DVD software. Note, however, that  
you can only change the region code up  
to four times. After the fourth change, the  
last region code entered becomes  
permanent, and cannot be changed.  
8
 
Tablet Dock User’s Guide  
Do not operate your media drive unless your  
system is sitting on a relatively flat surface.  
Using the drive when the system is not level  
may damage the drive or prevent proper  
operation.  
LOADING MEDIA  
(Refer to Figure 8 for the following steps)  
To load a disc into your media player drive,  
follow these steps:  
1. Push and release the eject button on the  
front of the drive to open the holder tray. The  
tray will come out of the system a short  
distance.  
2. Gently pull the tray out until a media disc  
can easily be placed in the tray.  
There may be a protective sheet in the tray  
from when it was shipped; please make sure  
it is removed before operating the drive.  
3. Place the media into the tray, label side up,  
with the hole in the center of the disc. Snap  
the disc onto the raised circle in the center  
of the tray.  
4. Gently push the holder tray back in until you  
hear a click.  
REMOVING MEDIA  
(Refer to Figure 8 for the following steps)  
1. Push and release the eject button on the  
front of the media player drive. This will stop  
the drive and the holder tray will come out  
of the system a short distance.  
2. Gently pull the tray out until the disc can  
easily be removed from the tray.  
Figure 8. Loading/Ejecting Media  
3. Carefully remove the media disc from the  
holder tray.  
4. Gently push the holder tray back in until  
youhear a click.  
9
 
Fujitsu Stylistic ST4000 Series Tablet Dock  
SAFETY PRECAUTIONS  
TABLET DOCK SPECIFICATIONS  
Never move the Tablet Dock with the  
system docked unless it is fully locked. If  
the system were to undock accidentally, it  
could drop and be damaged.  
Feature  
Ports  
Details  
• 100-pin docking connector  
• VGA, D-sub 15-pin female  
connector, DDC compliant  
• Line Out Jack (3.5mm) for  
head-phones or external  
speakers  
• DC input, 16VDC  
• IEEE 1394, 4-pin standard  
connector  
• USB (Universal Serial Bus)  
Ports (quantity: 3)  
Never power-off or remove the computer  
from the Tablet PC while the system is  
reading or writing to a floppy or hard drive.  
This could result in data loss.  
Always wait at least 5 seconds before  
restarting the Tablet PC after turning it off.  
Failure to do this can result in damage to  
the system’s electrical circuitry.  
• LAN connector: 100Base-  
TX/10Base-T; RJ-45  
• System Bay: Accommodates  
CD-ROM or DVD/CD-RW  
drive  
Power  
16VDC, with current of 3.75 A  
Dimensions  
• Height: 12.95” (329mm)  
• Width: 8.66” (220mm)  
• Depth: 10.35” (263mm)  
Weight  
• 5.95 lbs. (2.7Kg)  
Environmental  
• Operating Temperature:  
40° -95° F (5°-35° C)  
• Storage Temperature:  
-5° -140° F (-20° -60° C)  
• Relative Humidity: 20-80%  
Table 1.Tablet Dock Specifications  
10  
 

Echo Blower PB 610 User Manual
EdgeStar Air Conditioner AP12000S 1 User Manual
Edimax Technology Network Router BR 6104KP User Manual
Exmark Lawn Mower 4500 421 User Manual
Exmark Lawn Mower 4501 191 RevA User Manual
Extron electronic Car Video System MTP 15 HD A User Manual
GEM Automobile 2005 User Manual
GE Telephone 29322 User Manual
Gilson Mixer 600CM User Manual
Gitzo Camcorder Accessories GT2531 User Manual