24V DRIVE, HIGH SPEED LINE THERMAL PRINTER
4” MECHANISM, WITH OR WITHOUT CUTTER
FTP-642MCL001/002
FTP-642MCL301/302
■ OVERVIEW
FTP-642MCL/FTP-622DCL Series is an ultra high speed line thermal
printer driven by 24 VDC, printing on 4-inch wide paper (112 mm/114
mm) .
This printer is compact and light weight, and the design allows easy
head maintenance, head cleaning and head replacement.
This printer is suitable for a variety of applications, such as POS
terminals, ticket machines, coupon machines, label printers, medical
instruments, etc. A printer with a specially designed cutter is also
available.
FTP-642MCL001
■ HIGHLIGHTS
• Ultra high speed printing
It can print at 80 mm/s (640 dotlines/s) maximum by using Fujitsu
Components' unique head drive control.
• Compact and lightweight
This printer has a low profile of only 20 mm, and a light weight of
approximately 125 g.
• Low power consumption
The peak current for head driving is approximately 4.1 A (at 80
mm/s printing speed, 50% printing ratio).
FTP-622CU101
• Easy head access
It is designed for easy head cleaning and head replacement.
• Paper auto loading function
Thermal paper can be loaded without head-up lever operation.
• ESC/POSTM*1 Commands
The commands conform to ESC/POSTM.
• Auto Cutter
Printer with auto cutter (full cut/partial cut ) is also available.
• UL Recognized
File No.E171434
*1 ESC/POSTM is a registered trademark of SEIKO EPSON Corp.
FTP-622DCL001
1
FTP-642MCL001/002/301/302
(Continued)
Item
Specifications
Part number
Interface
FTP-642MCL001/002
FTP-642MCL301/302
Centronics (ESC/POSTM), RS232C
24VDC ± 5%, Voltage
2
Current : average*
(
): Peak
For head
1.61 (2.03) A (at 80 mm/s printing speed, 25% printing ratio)
1.17 (2.03) A (at 50 mm/s printing speed, 25% printing ratio)
1.08 (1.16) A (at 30 mm/s printing speed, 25% printing ratio)
Power supply
For motor
24VDC ± 5%, 1.0 A maximum
24VDC ± 5%, 1.0 A maximum
For cutter
----------
For logic
5VDC ± 5%, 0.5 A maximum
138 (W) × 48 (D) × 20 (H) mm (excluding lever)
131 (W) × 89 (D) × 24 (H) mm
approximately 125 g
Mechanism (cutter)
Interface board
147 (W) × 69 (D) × 42 (H) mm (w/cutter)
Dimension
Weight (Mechanism+Cutter)
Mechanism
approximately 450 g (w/cutter)
Pulse durability : 1 × 108 pulse/dot (using Fujitsu Takamisawa's standard
driving method)
Wear resistance
: 50 km (at 25% printing ratio)
Expected life
Cutter
----------
3 × 105 cuts
3
Operating temperature 0 to +50°C*
Environmental
conditions
Operating humidity
Storage temperature
Storage humidity
Head temperature
Paper out/Mark detect
Head-up
20 to 85% RH (no condensation)
–20 to +60°C (excluding paper)
5 to 95% RH (no condensation)
By thermistor (applied energy control, abnormal temperature detection)
By photointerrupter
Detection
By microswitch
For front insertion use (112 mm width) : FTP-040PU001, FTP-040P0701
For rear insertion use (114 mm width) : FTP-040P0020, FTP-040P0702
*Recommended papers
Recommended thermal sensitive paper
· Oji paper
· NIPPON paper
· MITSUBISHI paper Mills
: PD150R, PD160R, PD170R
: TF50KS-E,TF60KS-E,TF60KJ-R
: P220VBB-1, AFP-235
*1: There may be exceptions.
*2: 24 VDC, minimum head resistance.
*3: Guarantee: +5°C ~+40°C.
3
FTP-642MCL001/002/301/302
■ DIMENSIONS
Mechanism
PAPER INSERTION(MCL001)
HEAD UP LEVER(AT HEAD DOWN)
20.1
CENTER OF PAPER
PAPER
INSERTION
(MCL002)
HEAD CONNECTOR
106.4(POSITIONING HOLE PITCH)
+
1
71.8–
65.7
Unit: mm
(137.5)
Mechanism with cutter
3—M 3(FIXING HOLE FROM UPPER SIDE)
CENTER OF PAPER
MCL301
PAPER
INSERTION
MCL302
PAPER
INSERTION
93.0
106.4(POSITIONING H0LE)
73.0
147
71.8±1
(75.3)
(80.6)
Note: all dimensions are nominal value.
Unit: mm
4
FTP-642MCL001/002/301/302
Interface board
130.8
120.7
116.8
87.6
19.1
5.1
5.1
CN2**
CN5
CN3
4—ø3.6
CN10
CN11*
CN13
5.1
5.1
43.2
86.4
105.4
120.7
*CN11 on FTP-622DCL011/111 & 622DSL011/012/112 only
**CN2 on FTP- 622DSL only
Unit: mm
5
FTP-642MCL001/002/301/302
■ CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM
1. Thermal Head
Head side : B16B-PH-K-S-2.2 (J.S.T.) or equivalent
Board side: PHR-16 (J.S.T.) or equivalent
No. Signal Comment
1
2
VH
VH
Power for head
Power for head
3
GND Head ground
4
GND Head ground
5
STB1 Print enable signal 1
STB2 Print enable signal 2
STB3 Print enable signal 3
6
7
8
TH*1
STB4 Print enable signal 4
LAT Print data latching signal
Temperature detection
9
10
11
12
13
14
15
16
STB5 Print enable signal 5
VDD Power for logic
CLK
DIN
Data transmission clock
Print data output signal
GND Head ground
VH Power for head
*1: Symbol: " " means a negative logic signal
Thermal head heat sink
Motor
Head up level
1, 2, 3, ......................................15, 16
Connector Pin No.
2. Motor connectors
3. Sensor connectors
Motor side : PHR-4 (J.S.T.) or equivalent
Board side : B4B-PH-K-S (J.S.T.) or equivalent
Sensor
: PHR-5 (J.S.T.) or equivalent
Board side : B5B-PH-K-S (J.S.T.) or equivalent
No. Signal Comment
No. Signal Comment
1
2
3
4
B
B
A
A
Stepping motor coil excitation
Stepping motor coil excitation
Stepping motor coil excitation
Stepping motor coil excitation
1
2
3
4
5
VSEN Power for paper sensor
PHE Photo interrupter emittor
PHK Photo interrupter cathode
SW1 Head up detect switch 1
SW2 Head up detect switch 2
6
FTP-642MCL001/002/301/302
4. Cutter
Mech side : EHR-4 (J.S.T.) or equivalent
Board side : B4B-EH (J.S.T.) or equivalent
No Cable Color
Name
1
2
3
4
White
White
Red
Home position 1
Home position 2
Motor energizing signal M+
Motor energizing signal M-
Black
■ FUNCTION
ITEM
ITEM
1.
2.
3.
4.
5.
6.
7.
Test printing
8.
Cutter trouble detection
Motor power save
Paper-out detection
9.
10.
11.
12.
13.
14.
Paper near end detection
Mark detection
Head-up detection
MCU trouble detection
Power on/off sequence protection
Motor protection
Abnormal temperature detection of thermal head
Blown fuse detection
Abnormal voltage detection of head
Hardware timer
■ INTERFACE, COMMAND, OPTIONS
Please refer to the FTP-622DCL DATA SHEET and the FTP-622DSL DATA SHEET for Interface, Command, and
Options.
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
Email: marcom@fcai.fujitsu.com
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
7
|
Fostex Portable Speaker FW405N User Manual
Frigidaire Film Camera FHWC3025M S W B User Manual
Fujitsu Air Conditioner AOU12RL2 User Manual
Fundex Games Board Games My MASH Destiny Diary Game User Manual
Garmin GPS Receiver 18X User Manual
Garmin GPS Receiver TBM850 User Manual
GE Double Oven 49 4540 User Manual
Gefen TV Cables ext hdboost 141 User Manual
GE Freezer FCM5SU User Manual
GE Monogram Oven ZSC1201 User Manual