Fusion Car Amplifier EN AT1100 User Manual

ENCOUNTER  
ACTIVE ENCLOSURES  
EN-AT1100, EN-AT1120  
Disclaimer  
The provided self adhesive feet are intended for initial site placement only, and are not to be considered a suitable method  
of securing the Active Enclosure. Always ensure the Active Enclosure is securely attached, to avoid movement.  
FUSION accepts no responsibility for damage or injury in relation to inappropriate securing of this product  
Product Specifications  
EN-AT1100  
300 Watts  
EN-AT1120  
360 Watts  
Max Power Rating  
Frequency Repsonse  
Bass Boost (Variable)  
Low Pass Filter (Variable)  
Tuning  
35Hz - 250Hz  
0 / + 18dB  
40Hz - 250Hz  
Bass Reflex  
30Hz - 250Hz  
0 / + 18dB  
40Hz - 250Hz  
Bass Reflex  
Woofer Size  
Fuse  
10”  
12”  
15 Amp  
15 Amp  
Tube Dimensions  
550mm x 306mm x 306mm  
21 11/16” x 12 1/16” x 12 1/16”  
590mm x 365mm x 365mm  
23 1/4” x 14 3/8” x 14 3/8”  
Control Descriptions  
LEVEL  
This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If the sound becomes  
distorted reduce the level.  
LOW PASS FILTER (LPF)  
This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce. This should be adjusted to  
blend with your main speakers. Typically, this will be set to around 100Hz (approximately the central position of the control knob).  
BASS  
This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound becomes distorted, reduce  
the amount of boost.  
REMOTE LEVEL CONTROLLER  
When connected, this allows further control over the level from a remote location, using the supplied lead.  
Installation  
Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near  
gas tanks, fuel lines, hydraulic lines or electrical wiring.  
DO NOT mount the Encounter Active Enclosure in such a way as to pinch or damage the wires.  
Make sure everything is firmly connected, before attaching the +12V wire. Make sure the +12V wire is fused as close as possible  
to the battery. ALWAYS use a fuse with the recommended rating.  
Two types of self-adhesive feet are included in the packaging. The rubber feet are to protect the bottom of the enclosure, or the  
surface it is mounted to. There are four feet, which correspond to four indentations (feet and indentations are the same shape) in  
the bottom of the enclosure end plates. Peel off the paper covering the rubber feet, and adhere to the indentations.  
There are also four Velcro feet (both hook and eye parts, both with self-adhesive properties) included. These are for assisting  
in fixing the location of the enclosure. Peel off the paper covering and adhere one part to the indentations in the enclosure end  
plates, and the matching part to the mounting surface. Always clean the surfaces before applying the adhesive part  
 

Eclipse Fujitsu Ten Car Stereo System CD2000 User Manual
Exido Hair Dryer 235 014 User Manual
Fisher Price Motorized Toy Car 73610 User Manual
Fisher Price Motorized Toy Car N9522 User Manual
Flymo Trimmer MT21 User Manual
Friedrich Air Conditioner EQ08M11 User Manual
Gaggenau Oven EB 204 205 User Manual
GE Microwave Oven PEB2060DMWW User Manual
GE Ventilation Hood ZV830 User Manual
GE Waffle Iron 840101500 User Manual