Fusion Car Amplifier RE AM45020 User Manual

REACTOR  
AMPLIFIERS  
RE-AM45020, RE-AM90010, RE-AM90040  
Amplifier Specifications  
RE-AM45020  
RE-AM90010  
RE-AM90040  
Max Power Rating  
Frequency Response  
Dimensions (mm)  
Power Ratings  
450 Watts  
900 Watts  
900 Watts  
10Hz - 40kHz  
10Hz - 250Hz  
10Hz - 40kHz  
285(L)x 280(W) x 62(H)  
355(L)x 280(W) x 62(H)  
405(L)x 280(W) x 62(H)  
90 Watts RMS per Channel  
@ 4 Ohms 1% THD+N  
240 Watts RMS x 1 Channel  
@ 4 Ohms 1% THD+N  
90 Watts RMS per Channel  
@ 4 Ohms 1% THD+N  
130 Watts RMS per Channel  
@ 2 Ohms 1% THD+N  
350 Watts RMS x 1 Channel  
@ 2 Ohms 1% THD+N  
125 Watts RMS per Channel  
@ 2 Ohms 1% THD+N  
250 Watts RMS Bridged Channels  
@ 4 Ohms 1% THD+N  
230 Watts RMS Bridged Channels  
@ 4 Ohms 1% THD+N  
Installation Guidelines  
1.  
2.  
3.  
4.  
5.  
Ensure the +12v lead is disconnected from the battery before you connect any new equipment.  
Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.  
Ensure the Amplifier is securely fastened to the vehicle to prevent damage in the event of an accident.  
Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.  
Ensure the mounting location has sufficient air flow around the amplifier. If the amplifier is mounted in an enclosed space a  
3” fan with ducting should be used to aid in air flow.  
6.  
7.  
Do not mount any amplifier on a subwoofer enclosure as extended exposure to vibration may cause malfunction of the  
amplifier.  
Ensure you use the recommended gauge wire/cable for all amplifier connections.  
Wiring  
Ensure the audio system is turned off before making any connections to the amplifier, speakers or source unit.  
Failure to do so could result in permanent damage to the audio system. When wiring the FUSION amplifier ensure  
that the cable is protected from sharp objects and always use rubber grommets when wiring through metal panels.  
Ensure all terminals and connections are protected from the vehicle chassis and from each other as failure to do so  
could result in permanent damage to the audio system.  
Power  
FUSION amplifiers should be connected directly to the +12v battery terminal with an inline fuse or circuit breaker as  
close to the battery as possible.  
Ground  
When grounding/earthing your amplifier ensure that the location is a good source of ground (preferably the floor  
pan). Make sure the metal is clean of paint etc as a poor earth could damage your audio system.  
Remote Turn On  
This connection turns the amplifier on and should be connected to the remote turn on wire from the Head Unit. If  
one is not available a switched 12v source must be used. Either a power antenna wire or ACC +12v.  
Low Level Inputs  
Choose the correct length RCA interconnects and run them to the RCA outputs of the source/head unit, avoiding  
running beside other looms and or power cable.  
Level Control  
This control is used to match the input level of the amplifier to the output level of you head unit. We recommend the  
following method.  
 

Fender Guitar Starcaster User Manual
Field Controls Range Oil Venting Systems User Manual
Fisher Price Baby Toy C5347 User Manual
Freecom Technologies Network Card Storage Gateway NETWORK HARD DRIVE User Manual
Frigidaire Oven FGEW2745K F W B User Manual
Furuno SONAR FE 808 User Manual
GE Answering Machine 20801800 User Manual
GE Monogram Ventilation Hood ZV36SSFSS User Manual
GE Thermostat RAK148P1 User Manual
Global Technology Associates Network Card GB 800 User Manual