Ver.3.10
AD12-16(PCI)E
PCI-bus Analog Input Multi-Function Board
AD12-16(PCI)E
This board is interface board of the PCI bus conformity
which inputs analog signal and performs conversion (AD
translation) to a digital signal.
A general-purpose type is Conversion speed: 10µsec/ch,
resolution: A/D conversion is performed by 12 bits.
By using attached API function library API-PAC(W32), the
application software for Windows can be created by the
various programming languages which are supporting
Win32API functions, such as Visual Basic, and Visual C/
C++.
Accessories (Option)
Accessories (Option)
Terminal unit for solderless terminal : DTP-3(PC)
Terminal unit for leads : DTP-4(PC)
Features
BNC connector relay terminal unit : ATP-16 *2
Solderless terminal relay terminal stand : FTP-15 *3
Solderless relay terminal unit : EPD-37 *2
Simultaneous sampling functional extension board :
ATSS-16 *2
Insulated funct ional extension board : ATII-8A *2
Low path filter extension board : ATLF-8 *2
Channel extension board : ATCH-16(PCI)
- Single end 16ch, 8ch differential(Analog input function)
Selection of a single, and input and differential input is
possible at the jumper on board. The turn of the channel to
change can be beforehand set as an exclusive register
arbitrarily. Moreover, extension (a maximum of 32
channels) of the number of input channels and a
simultaneous sampling are realizable by using optional
unit.
- Buffer memory loading(Analog input function)
The buffer memory for 256K data which can be used in
FIFO or ring form is carried on board. The sampling as
background processing independent of the throughput of a
personal computer is possible.
*2 Op tion cable of PCB37PS-*P is required (0.5m is
recommended).
*3 Opt ion cable of DT/E2 and PCB15P-1.5 are required.
Cable & Connector (Option)
- Colorful sampling control function(Analog input function)
A start/stop of a sampling can detect and control the size
of not only the command of software but analog signal, and
the signal of T TL level. Moreover, selection of the internal
sampling clock which uses t he clock generator of board
loading, and the external sampling clock which uses the
digital signal inputted from the outside is possible for the
sampling clock which determines sampling speed.
- Analog output function
Cable (Option)
37pin D-SUB 37-pin flat cable : PCA37P-1.5
37pin D-SUB 37-pin shield cable :
PCA37PS-*P (0.5m, 1.5m)
37pin D-SUB 37 pin D-SUB shield cable :
PCB37PS-*P (0.5m, 1.5m)
15pin D-SUB 15pin flat cable : PCA15P-1.5
15pin D-SUB both-ends connector flat cable :
PCB15P-1.5 *1
Analog output function of one channel is carried.
- Digit al I/O function
Coaxial cable for single end input (16ch) :
PCC16PS-* (1.5m, 3m)
It has four digit al inputs of TTL level, and four digital
outputs, and the monitor of external apparatus and control
can be performed.
2pin shield cable for 16ch (8ch) : PCD8PS-* (1.5m, 3m)
16pin flat cable(1.5m) : DT/E1
15pin D-SUB conversion cable : DT/E2
- Abundant Option
*1 FTP-15 is required only at the time of use.
Furthermore, the option apparatus which extends a
function can be used.
By using option apparatus, a functional rise and
connection can be performed easily.
Please refer to "cable connector" and "accessories" about an
option.
Packing List
- Board [AD12-16(PCI)E] - 1
- User's Guide - 1
- CD-ROM [API-PAC(W32)] - 1
1
Ver.3.10
AD12-16(PCI)E
External Connection
Connection method with a connector
Connection between this board and external apparatus is made by the interface connector on board (CN1 and CN2).
Interface connector has two, the object for analog I/O (CN1: D-SUB 37pin Female), and the object for control signals, such as
digital I/O and counter control, (CN2: 16pin Pin-header).
I nter face connector(CN1)
37
19
- Connector used
A 37pin D type connector [F (female)type]
DCLC-J37SAF-20L9 [mfd.by JAE ] equivalent
20
1 - Applicable connector
17JE-23370-02(D8C) [mfd by DDK, M(male)type]
Interface connector (CN 3)
Interface connector (CN 2)
CN1
CN2
B8
B1
A8
It is the connector (CN 3) f or ATUH -16(PCI )
- Applicable connector
PS-16SEN-D4P1-1C [mfd.by JAE]
A1
Examples of Connecting Options
The accessory with this
Relay terminal stand
mark ca n be mounted on
a DIN rail by using
DIN-ADP1.
Terminal unit
EPD-37
16CH Multiplexer Sub-Board
ATUH-16(PCI)
*
A n external power supply is
required to use a combination of
channel expansion and extension
boards.
For Solder Terminal
DTP-3(PC)
*1-m shielded cable bundled
Option
Cable
*1 : PCB 37PS-0.5 P is
recommended .
PCB37PS * 1
For leads
Analog E Series
DTP-4(PC)
*1-m shielded cable bundled
Option
Cable
For BNC connector
ATP-16
PCC16PS
PCD8PS
Extended functional
board
Extended functional
board
Option
Cable
Isolated functional
extension
ATII-8A
Isolated functional
extension
ATII-8A
PCB37PS *1
PCA37PS
PCA37P
Relay terminal sta nd
Extended functional
board
Terminal unit
EPD-37
Option
Cable
16 Channel
Simultaneous Sample
ATSS-16
Digital I/O Cable
DT/E1
PCB37PS *1
For Solder Terminal
DTP-3(PC)
*1-m shielded
cable bundled
Low path filter
extension board
ATL F-8
Option
Cable
Option
Cable
For leads
PCA15P
DTP-4(PC)
* 1-m shielded
cable bundled
PCA37PS
PCA37P
Digital I/O
Cable
DT/E2
Relay terminal stand
Option
Cable
For BNC connect or
ATP-16
Multi-function board
FTP-15
PCB15P
3
AD12-16(PCI)E
Ver.3.10
Connector Pin Assignment
<Single-Ended Input>
<Differential Input>
CN1
CN1
19
+5V DC fr om PC
Simultaneous Hold Output
Analog Output
19
18
17
16
15
14
13
12
11
10
9
+5V DC from PC
Digital Gr ound
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
Digit al Ground
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
Analog Gr ound
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
18
17
16
15
14
13
12
11
10
9
Simultaneous Hold Output
Analog Output
Analog Input 15
Analog Input 7 [
Analog Input 7 [+]
Analog Input 6 [
Analog Input 6 [+]
Analog Input 5 [
Analog Input 5 [+]
Analog Input 4 [
Analog Input 4 [+]
Analog Input 3 [
Analog Input 3 [+]
Analog Input 2 [
Analog Input 2 [+]
Analog Input 1 [
Analog Input 1 [+]
Analog Input 0 [
Analog Input 0 [+]
-]
Analog Input
7
Analog Input 14
Analog Input
Analog Input 13
Analog Input
Analog Input 12
Analog Input
Analog Input 11
Analog Input
Analog Input 10
-]
6
-]
5
-]
4
8
8
-]
7
3
7
6
6
-]
5
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
2
9
1
8
0
5
4
4
-]
3
3
2
2
-]
1
1
Analog Input 0
Analog input signals in single-ended input mode.
The numbers correspond to channel numbers.
to Analog Input 15
Analog Input 0[+]
to Analog Input 15[+]
Analog Input 0[-]
to Analog Input 15[-]
Analog Output
Analog input signals in differential input mode.
The numbers correspond to channel nu mbers.
Analog input signals in differential input mode.
The numbers correspond to channel numbers.
Analog output signal
Analog Ground
Analog ground common to analog I/O signals.
Simultaneous Hold
Output
Control signal for simultaneous sampling unit ATSS -16 available as an
option.
+5V DC from PC
Digital Ground
Supplies 3 amperes of current at +5 volts.
Digital ground common to "Simultaneous Hold Output" and "+5V DC from
PC".
Notes!
- Please connect each output and power supply output neither with analog ground nor digital ground too hastily.
- Moreov er, please do not connect output and output. It becomes the cause of failure.
CN2
N. C.
Digital Gr ound
B8 A8
B7 A7
B6 A6
B5 A5
B4 A4
B3 A3
B2 A2
B1 A1
+5V DC fr om PC
Sampling Clock Output
Exter nal Stop Trigger I nput
Digital Input 3 / INT Tr igger
Digital Input 1 / CNT Gate
Digital Gr ound
Digital Output 2
Digital Output 0
Exter nal Sampling Clock Input
External St ar t Trigger Input
Digital I nput 2 / CNT Clock
Digital Input 0
Digital Output 3 / CNT Output
Digital Output 1
Digital Input 0
Digital Input 1
/CNT Gate
Digital Input 2
/CNT Clock
Digital input signal.
Digital input signal.
Also serving as the counter gate control input signal.
Digital input signal.
Also serving as the clock input signal
Digital Input 3
/INT Trigger
Digital Out 0
to Digital Out 2
Digital Out 3
to CNT Output
Digital input signal.
Also serving as the interrupt input signal.
Digital output signal.
Digital output signal.
Capable of being jumper-switched to serve as the counter output
signal.
External Start Trigger Input
External Stop Trigger Input
External Sampling Clock
Input
External trigger input signal for sampling start conditions
External trigger input signal for sampling stop conditions
External sampling clock input signal
Sampling Clock Output
+5V DC from PC
Digital Ground
N.C.
Sampling clock output signal
Supplies 1 ampere of current at +5 volts.
Digital ground common to the signals and “ +5V DC from PC” .
No connection to this pin.
Notes!
- Please connect each output and power supply output neither with analog ground nor digital ground too hastily.
- Moreov er, please do not connect output and output. It becomes the cause of failure.
4
Ver.3.10
AD12-16(PCI)E
Analog Input Connection
The input form of analog signal has a single and input, and different ial input, and the connection methods with a signal differ,
respectively. Here, the example in the case of connecting using a flat cable or a shield cable is shown.
Single-ended Input
It is example of connection when using cables, such as optional flat cable (PCA37P).
The source of a signal and a ground are connected to 1 to 1 to each analog input channel of CN1.
BOARD
CN1
Cable
Signal Source
Analog Input 0 ..1 5
Analog Ground
It is the example of connection which used shield cables, such as an optional coaxial cable (PCC16PS). When the distance of the
source of a signal and a board is long, please use it to enlarge noise-proof nature. To each analog input channel of CN1, wire line is
connected to signal line and the group edited by the shield is connected to a ground.
BOARD
CN1
Shield cable
Signal Source
Analog Input 0 ..1 5
Analog Ground
Notes!
- When a frequency ingredient 1MHz or more is contained in the source of signal, the cross talk between channels may occur.
- When a board and the source of a signal are influenced of a noise, or when the distance of a board and the source of a signal is
long, it may be unable to input in exact data by the connection method.
- Analog signal to input must not exceed the maximum input voltage on the basis of the analog ground of a board. It may
damage, when it exceeds.
- Conversion data is unknown when input terminal is not connected. Please connect with analog ground too hastily the input
terminal of a channel which is not connected to the source of a signal.
Differential Input
It is example of connection when using cables, such as optional flat cable (PCA37P).
[+] input of each analog input channel of CN1 is connected t o a signal, and [-] input is connected to t he ground of the source of a
signal. Furthermore, the analog ground of a board and the ground of the source of a signal are connected.
CN1
Cable
Signal Source
BOARD
Analog Input 0[+]..7[+]
Analog Input 0[-]..7[-]
Analog Ground
It is the example of connection which used shield cables, such as optional 2 heart shield cable (PCD8PS). When the distance of the
source of a signal and a board is long, please use it to enlarge noise-proof nature. [+] input of each analog input channel of CN1 is
connected to a signal, and [-] input is connected to the ground of the source of a signal. Furthermore, the analog ground of a board
and the ground of the source of a signal are connected in the group edit ed by the shield.
CN1
Shield cable
Signal Source
BOARD
Analog Input 0[ +] ..7 [+]
Analog Input 0[ -]. .7[ -]
Analog Ground
Notes!
- When a frequency ingredient 1MHz or more is contained in the source of signal, the cross talk between channels may occur.
- Conversion data becomes unfixed when analog ground is not connected.
- When a board and the source of a signal are influenced of a noise, or
when the distance of a board and the source of a
signal is long, it may be unable to input in exact data by the connection method.
- Analog signal inputted into [+] input and [-] input must not exceed the maximum input voltage on the basis of the analog
ground of a board. It may damage, when it exceeds.
- Conversion data when having not connected terminal of [+] input or [-] input is unfixed. Both should connect with an analog
ground too hastily the terminal of [+] input of the channel which does not connect with the source of a signal, and [-] input.
5
AD12-16(PCI)E
Ver.3.10
Analog Output Connection
The example in the case of connecting an analog output signal using a flat cable or a shield cable is shown.
It is example of connection when using cables, such as optional flat cable (PCA37P).
The analog output and analog ground of CN1 are connected to the input and ground of external apparatus.
BOARD
CN1
Cable
Target
Analog Output
Analog Ground
It is the example of connection which used the shield cable. Please use it to enlarge the case where the distance of a board and
external apparat us is long, and noise-proof nature. To the analog output of CN1, wire line is connected to a signal line and the
group edited by the shield is connected to a ground.
Target
BOARD
CN1
Shield cable
Analog Output
Analog Ground
Notes!
- When a board and a target are influenced of noise, or when the distance of a board and a target is long, exact data may be
unable to be outputted depending on the connection method.
- The maximum output current capacity of analog output signal is +/-5mA. Please connect with a board after checking the
specification for connection.
- Please connect analog output signal neither with analog ground nor digital ground too hastily. It becomes the cause of failure.
Digital I/O Connection
The example in t he case of connecting a digital I/O signal and control signals (external trigger input signal, sampling clock output
signal, etc.) using a flat cable is shown.
CN2 and external apparatus are connected using optional flat cable (DT/E1), 15p in D-SUB connector (DT/E2) with a bracket , etc.
All of these digital I/O signals and a control signal are the signals of TTL level.
Digital Input Connection
CN2
Cable
Target
10k Ohm
BOARD
Input
Digital Ground
Digital Output Connection
CN2
Cable
Target
BOARD
Output
I OL=24mA
Digital Ground
Note!
- Please connect each output neither with analog ground nor a digital ground too hastily. It becomes the cause of failure.
6
Ver.3.10
AD12-16(PCI)E
Block Diagram
16 single-ended / Analog Outputs
8 differentia l
A nalog Inputs
Simultaneous
Hold
4 Digital Input /
4 Digital Output /
control signals
Counter
signals
CN1
CN2
8/16 channel
multiplexer
with over voltage
pr otection
D/A
convert er
Instrument
amplifier
Sample & Hold
amplifier
Counter 8254
ASIC
16-bit counter 2
16-bit counter 1
16-bit counter 0
A/D
converter
DC/DC
converter
On board
memory
PCI Bus interface
PCI Bus
All data subject to change without notice.
7
|